Gebruiksaanwijzing /service van het product TRV93 van de fabrikant Sony
Ga naar pagina of 88
3-861-891- 13 (1) Video Camera Recor der ©1998 by Sony Corporation CCD-TRV75/TRV85/TRV93/ TRV715/TRV815 CCD-TRV93 Model No. CCD-TRV Model No. AC-L Serial No. Serial No. Operating Instructions Before operating the unit, please read this manual thoroughly, and retain it for future reference.
2 Welcome! Congratulations on your purchase of this Sony Handycam Vision TM camcorder. With your Handycam Vision, you can capture life’s precious moments with superior picture and sound quality. Your Handycam Vision is loaded with advanced features, but at the same time it is very easy to use.
3 T able of contents Before you begin Using this manual ................................... 4 Checking supplied accessories .............. 5 Getting started Installing and charging the battery pack .....................................................
4 [a] [ b] Before you begin The instructions in this manual are for the four models listed below. Before you start reading this manual and operating the unit, check your model number by looking at the bottom of your camcorder. The CCD-TRV93 is the model used for illustration purposes.
5 Checking supplied accessories Check that the following accessories are supplied with your camcorder. 1 Wireless Remote Commander (1) (p. 83) 2 AC-L10A/L10B/L10C AC power adaptor (1), Power cord (1) (p. 7, 25) 3 NP-F330 Battery pack (1) (p. 6, 25) 4 CR2025 Lithium Battery (1) (p.
6 Before using your camcorder, you first need to install and charge the battery pack. This camcorder operates only with the “InfoLITHIUM” battery. “InfoLITHIUM” is a trademark of Sony Corporation. Installing the battery pack ( 1 ) While pressing BATT RELEASE, slide the battery terminal cover in the direction of the arrow.
7 Getting started Installing and charging the battery pack Charging the battery pack Charge the battery pack on a flat surface without vibration. The battery pack is charged a little in the factory. ( 1 ) Open the DC IN jack cover and connect the supplied AC power adaptor to the DC IN jack with the plug’s 4 mark up.
8 Charging time Battery NP-F330 NP-F530/F550 NP-F730/F730H/ NP-F930/F950 pack (supplied) F750 Charging 150 210 300 390 time* (min.) (90) (150) (240) (330) The time required for a normal charge is indicated in parentheses. * Approximate minutes to charge an empty battery pack using the supplied AC power adaptor.
9 Getting started CCD-TRV93 Battery NP-F330 NP-F530 NP-F550 NP-F730 NP-F730H NP-F930 NP-F950 pack (supplied) /F750 Continuous 125 (110) 215 (190) 250 (220) 430 (385) 510 (460) 680 (610) 780 (700) reco.
10 Make sure that the power source is installed. When you want to record in the Hi8 system, use Hi8 video cassette H . ( 1 ) While pressing the small blue button on the EJECT switch, slide it in the direction of the arrow. The cassette compartment automatically lifts up and opens.
11 Basic operations Basic operations Camera r ecording Make sure that the power source is installed and a cassette is inserted and that the START/STOP MODE switch inside the LCD panel is set to . Before you record one- time events, you may want to make a trial recording to make sure that the camcorder is working correctly.
12 L O C K START/STOP S T A N D B Y START/STOP L O C K S T A N D B Y STBY 0:35:20 L O C K START/STOP S T A N D B Y To stop recording momentarily [a] Press START/STOP again. The “STBY” indicator appears in the viewfinder (Standby mode) . To finish recording [b] Press START/STOP again.
13 Basic operations Camera recording Note on Standby mode If you leave the camcorder in Standby mode for 5 minutes while the cassette is inserted, the camcorder turns off automatically for saving battery power as well as for preventing the battery and tape from wearing down.
14 T W T W [a] [b] Using the zoom feature Zooming is a recording technique that lets you change the size of the subject in the scene. For more professional-looking recordings, use the zoom function sparingly.
15 Basic operations Selecting the START/STOP mode Your camcorder has three modes. These modes enable you to take a series of quick shots resulting in a lively video. ( 1 ) While pressing OPEN, open the LCD panel. ( 2 ) Set START/STOP MODE to the desired mode.
16 Shooting with the LCD screen You can also record the picture while looking at the LCD screen. When using the LCD screen, the viewfinder turns off automatically. You cannot monitor the sound from the speaker during recording. ( 1 ) While pressing OPEN, open the LCD panel.
17 Basic operations Notes on the LCD panel • When closing the LCD panel, turn it vertically until it clicks [ a ] . • When turning the LCD panel, turn it always vertically; otherwise, the camcorder body may be damaged or the LCD panel may not close properly [ b ] .
18 Hints for better shooting [a] [b] For hand-held shots, you’ll get better results by holding the camcorder according to the following suggestions: • Hold the camcorder firmly and secure it with the grip strap so that you can easily manipulate the controls with your thumb.
19 Basic operations Hints for better shooting Place the camcorder on a flat surface or use a tripod Try placing the camcorder on a table top or any other flat surface of suitable height. If you have a tripod for a still camera, you can also use it with the camcorder.
20 Using EDITSEARCH, you can review the last recorded scene or check the recorded picture in the viewfinder or on the LCD screen. ( 1 ) While pressing the small green button on the POWER switch, set it to CAMERA.
21 Basic operations Playing back a tape You can monitor the playback picture on the LCD screen. ( 1 ) While pressing the small green button on the POWER switch, set it to VTR. The video control buttons light up. ( 2 ) Insert the recorded tape with the window facing out.
22 When monitoring on the LCD screen You can turn the LCD panel over and move back to the camcorder with the LCD screen facing out [ a ] . You can adjust the angle of the LCD screen by turning the LCD screen up to 15 degrees [ b ] . Using the remote commander You can control playback using the supplied Remote Commander.
23 Basic operations Playing back a tape Various playback modes You can enjoy clear pictures on the LCD screen during still, slow and picture search. (Crystal-clear still/slow/picture search) To view a still picture (playback pause) Press P during playback.
24 2 1 END SEARCH You can go to the end of the recorded portion after you record and play back the tape to make the transition between the last scene you recorded and the next scene smooth. The tape starts rewinding or fast-forwarding and the last 5 seconds (10 seconds in LP mode) of the recorded portion play back.
25 Advanced operations You can choose any of the following power sources for your camcorder: battery pack, house current, alkaline batteries (CCD-TRV75/TRV85/TRV93 only) and 12/24 V car battery. Choose the appropriate power source depending on where you want to use your camcorder.
26 Using alkaline batteries – CCD-TRV75/TRV85/TRV93 only Use the battery case (supplied) and six size AA (LR6) Sony Alkaline batteries (not supplied).
27 Advanced operations Using a car battery Use Sony DC-V515A car battery charger (not supplied). Connect the car battery cord to the cigarette lighter socket of a car (12 V or 24 V).
28 Changing the mode settings You can change the mode settings in the menu system to further enjoy the features and functions of the camcorder. ( 1 ) Press MENU to display the menu. ( 2 ) Turn the control dial to select the desired icon in the left side of the menu, then press the dial.
29 Advanced operations Notes on changing the mode setting • Menu items differ depending on the setting of the POWER switch to VTR or CAMERA. • When you let the subject monitor the shot (mirror mode), the menu display does not appear. Selecting the mode setting of each item Items for both CAMERA and VTR modes LCD B.
30 Changing the mode settings AUTO TV ON* <ON/OFF> You can use this feature only with Sony TVs. • Select ON to turn on the TV automatically when using the LASER LINK function.
31 Advanced operations Items for CAMERA mode only D ZOOM* <ON/OFF> • Select ON to activate digital zooming. • Select OFF to not use the digital zoom. The camcorder goes back to 18x zoom. 16:9WIDE* <OFF/CINEMA/16:9FULL> • Normally select OFF.
32 Changing the mode settings WORLD TIME* Select this item to set the clock by a time difference. REC LAMP* <ON/OFF> • Select OFF when you do not want the camera recording/battery lamp at the front of the unit to light up. • Normally select ON.
33 Advanced operations When you shoot a subject with the light source behind the subject or a subject with a light background, use the BACK LIGHT function. Press BACK LIGHT. The c indicator appears in the viewfinder or on the LCD screen. [ a ] Subject is too dark because of backlight.
34 Selecting the fader function You can fade in or out to give your recording a professional appearance. When the picture fades in, the sound gradually increases.When the picture fades out, the sound gradually decreases. Using the F ADER function FADER M.
35 Advanced operations Using the fader function When fading in [a] ( 1 ) While the camcorder is in Standby mode, press FADER until the desired fade indicator flashes. ( 2 ) Press START/STOP to start recording. The fade indicator stops flashing. When fading out [b] ( 1 ) During recording, press FADER until the desired fade indicator flashes.
36 OFF ON The NightShot function enables you to shoot a subject in a dark place. You can achieve a satisfactory recording of the ecology of nocturnal animals for observation with this function. This function may record picture nearly in monochrome. ( 1 ) While the camcorder is in Standby mode, slide NIGHTSHOT to ON.
37 Advanced operations Selecting the desired mode You can record a cinemalike picture (CINEMA) or a 16:9 wide picture to watch on the 16:9 wide-screen TV (16:9 FULL). CINEMA Black bands appear at the top and the bottom of the screen, and the viewfinder or LCD screen [a] and a normal TV screen [b] look wide.
38 Using the wide mode function Using the wide mode function You can select the wide mode (OFF, CINEMA, 16:9FULL) in the menu system (p. 28). To cancel wide mode Select OFF in the menu system. To watch the tape recorded in wide mode To watch the tape recorded in CINEMA mode, set the screen mode of the wide-screen TV to zoom mode.
39 Advanced operations Selecting the best mode You can select one of six PROGRAM AE (Auto Exposure) modes to suit your shooting situation, referring to the following.
40 Using the PROGRAM AE function ( 1 ) Press PROGRAM AE. ( 2 ) Turn the control dial to select the desired PROGRAM AE mode. To turn off program AE Press PROGRAM AE.
41 Advanced operations [a] [b] [c] [d] Focusing manually When to use manual focus In the following cases you should obtain better results by adjusting the focus manually. • Insufficient light [ a ] • Subjects with little contrast - walls, sky, etc.
42 To return to autofocus mode Set FOCUS to AUTO. The f indicator in the viewfinder or on the LCD screen disappears. Shooting in relatively dark places Shoot at wide-angle after focusing in the telephoto position. To record a very distant subject Push FOCUS down to INFINITY.
43 Advanced operations [a] [b] [c] [d] [e] [f] Enjoying pictur e effect Selecting picture effect You can make pictures like those of television with the Picture Effect function. PASTEL [a] The contrast of the picture is emphasized, and the picture looks like an animated cartoon.
44 Using picture effect function ( 1 ) Press PICTURE EFFECT. ( 2 ) Turn the control dial to select the desired picture effect mode. To turn off picture effect Press PICTURE EFFECT.
45 Advanced operations When to adjust the exposure Adjust the exposure manually under the following cases. [ a ] • The background is too bright (back lighting) • Insufficient light: most of the picture is dark [ b ] • Bright subject and dark background • To record the darkness faithfully Adjusting the exposure ( 1 ) Press EXPOSURE.
46 Shooting with the sun behind you If the light source is behind your subject, or in the following situations, the subject will be recorded too dark. • The subject is indoors and there is a window behind the subject. • Bright light sources are included in the scene.
47 Advanced operations Superimposing a title You can select one of eight preset titles and two custom titles. You can also select the language, color, size and position of titles. Superimposing titles ( 1 ) Press TITLE to display the title menu. ( 2 ) Turn the control dial to select , then press the dial.
48 To superimpose the title from beginning After step 7, press START/STOP to start recording. To superimpose the title while you are recording After pressing START/STOP to start recording, start from step 1. In this case, beep is not heard. To select the language of preset title When you want to select the language, select before step 2.
49 Advanced operations Making your own titles You can make up to two titles and store them in the camcorder. We recommend to set the POWER switch to VTR or eject the cassette before you begin. Your title can have up to 20 characters. ( 1 ) Press TITLE to display the title menu.
50 To edit a title you have stored In step 3, select CUSTOM1 or CUSTOM2, depending on which title you want to edit, then change the title. Note You can not enter over 20 characters title. If you take 5 minutes or longer to enter characters while a cassette is in the camcorder The power goes off automatically.
51 Advanced operations Use this feature to check the tape condition before recording, so that you can get the best possible picture (ORC). ( 1 ) While the camcorder is in Standby mode, press MENU to display the menu. ( 2 ) Turn the control dial to select Ò , then press the dial.
52 – CCD-TRV93 only You can use the built-in light to suit your shooting situation. The recommended distance between the subject and camcorder is about 5 feet (1.5 meters). While the camcorder is in Standby mode, slide LIGHT to ON. The built-in light turns on.
53 Advanced operations Replacing the bulb Use the Sony XB-3D halogen lamp (not supplied). The supplied halogen lamp is not on the market. Purchase the Sony XB-3D halogen lamp. Remove the power source before replacing the bulb. ( 1 ) While pushing the hole under the built-in light unit using a wire, remove the unit.
54 When the Steady Shot function is working, the camcorder compensates for camera- shake. You can release the Steady Shot function when you do not need to use the Steady Shot function. The “ ” indicator appear in the viewfinder or on the LCD screen.
55 Advanced operations Connect the camcorder to your TV or VCR to watch the playback picture on the TV screen. When monitoring the playback picture by connecting the camcorder to your TV, we recommend you to use house current for the power source. While playing back on a TV screen, close the LCD panel.
56 Using the AV cordless IR receiver Once you connect the AV cordless IR receiver (not supplied) having the LASER LINK mark to your TV or VCR, you can easily view the picture on your TV. For details, refer to the operating instructions of the AV cordless IR receiver.
57 Advanced operations Editing onto another tape You can create your own video program by editing with any other h 8 mm, H Hi8, j VHS, k S-VHS, VHSC, K S-VHSC, l Betamax or ¬ ED Betamax VCR that has video/audio inputs. Before editing Connect the camcorder to the VCR using the supplied A/V connecting cable.
58 Recor ding from a VCR or TV You can record a tape from another VCR or a TV program from a TV that has video/ audio outputs. Connect the camcorder to the VCR or TV using the supplied A/V cable. Turn down the volume of the camcorder while editing. Otherwise, picture distortion may occur.
59 Additional information (+) (--) - Additional information Changing the lithium battery in the camcor der Your camcorder is supplied with a lithium battery installed. When the battery becomes weak or dead, the I indicator flashes in the viewfinder for about 5 seconds when you set the POWER switch to CAMERA.
60 Changing the lithium battery When replacing the lithium battery, keep the battery pack or other power source attached. Otherwise, you will need to reset the date, time and other items in the menu system retained by the lithium battery. ( 1 ) Open the LCD panel and open the lid of the lithium battery compartment.
61 Additional information You can reset the date and time in the menu system. ( 1 ) While the camcorder is in Standby mode, press MENU to display the menu. ( 2 ) Turn the control dial to select , then press the dial. ( 3 ) Turn the control dial to select CLOCK SET, then press the dial.
62 Simple setting of clock by time differ ence You can easily set the clock for a local time by a time difference in the menu system. ( 1 ) While the camcorder is the standby mode, press MENU to display the menu. ( 2 ) Turn the control dial to select , then press the dial.
63 Additional information Usable cassettes and playback modes Selecting cassette types This Hi8 system is an extension of the standard 8 mm system, and was developed to realize higher picture quality. You can use either Hi8 or standard 8 mm video cassette for this camera.
64 Tips for using the battery pack This section shows you how you can get the most out of your battery pack. Preparing the battery pack Always carry additional batteries Have sufficient battery pack power to do 2 to 3 times as much recording as you have planned.
65 Additional information Tips for using the battery pack Notes on the rechargeable battery pack Caution Never leave the battery pack in temperatures above 140°F (60°C), such as in a car parked in the sun or under direct sunlight. The battery pack heats up During charging or recording, the battery pack heats up.
66 Tips for using the battery pack Notes on the “InfoLITHIUM” battery pack What is “InfoLITHIUM” The “InfoLITHIUM” is a lithium ion battery pack which can exchange data with compatible video equipment about its battery consumption. Sony recommends that you use the “InfoLITHIUM” battery pack with video equipment having the mark.
67 Additional information Maintenance information and pr ecautions Notes on the battery case – CCD-TRV75/TRV85/TRV93 only • Use only with alkaline batteries. You cannot use the battery case with manganese batteries or size AA (LR6) rechargeable NiCd batteries.
68 Video head cleaning To ensure normal recording and clear pictures, clean the video heads. When the v˚ indicator and “ CLEANING CASSETTE” message appear one after another or playback pictures are “noisy” or hardly visible, the video heads may be dirty.
69 Additional information Removing dust from inside the viewfinder – CCD-TRV75/TRV85/TRV715/TRV815 only ( 1 ) Remove the screw with a screwdriver (not supplied). Then, while sliding the RELEASE knob, turn the eyecup in the direction of the arrow and pull it out.
70 Maintenance information and precautions Precautions Camcorder operation • Operate the camcorder on 7.2 V (battery pack) or 8.4 V (AC power adaptor).
71 Additional information Maintenance information and precautions AC power adaptor • Unplug the unit from the wall outlet when not in use for a long time. To disconnect the power cord, pull it out by the plug. Never pull the power cord itself. • Do not operate the unit with a damaged cord or if the unit has been dropped or damaged.
72 Using your camcor der abroad Each country or area has its own electric and TV color systems. Before using your camcorder abroad, check the following points. Power sources You can use your camcorder in any country or area with the supplied AC power adaptor within 100 V to 240 V AC, 50/60 Hz.
73 Additional information If you run into any problem using the camcorder, use the following table to troubleshoot the problem. Should the difficulty persist, disconnect the power source and contact your Sony dealer or local authorized Sony service facility.
74 Trouble check Symptom Cause and/or Corrective Actions • The START/STOP MODE switch is set to 5SEC or . m Set it to . (p. 15) • The battery is dead. m Use a charged battery pack or the AC power adaptor. (p. 7, 25) • Moisture condensation has occurred.
75 Additional information Trouble check Symptom Cause and/or Corrective Actions • COMMANDER is set to OFF in the menu system. m Set it to ON. (p. 30) • Something is blocking the infrared rays. m Remove the obstacle. • The batteries are not inserted with the correct polarity.
76 Self-diagnosis display C:21:00 The camcorder has a self-diagnosis display. This function displays the camcorder’s condition with five digits (a combination of a letter and figures) in the viewfinder or on the LCD screen. If this occurs, check the following code chart.
77 Additional information Storage temperature –4°F to +140°F (–20°C to +60°C) Dimensions (Approx.) CCD-TRV75/TRV85/TRV715/ TRV815: 4 1/2 x 4 3/8 x 8 1/2 in. (114 x 111 x 214 mm) (w/h/d) CCD-TRV93: 4 1/2 x 4 3/8 x 8 1/2 in. (114 x 109 x 214 mm) (w/h/d) Mass (Approx.
78 Identifying the parts 1 EDITSEARCH button (p. 20) 2 LASER LINK button (p. 56) 3 Lens cover 4 POWER switch (p. 11) 5 FOCUS switch (p. 42) 6 NEAR/FAR dial (p. 42) 7 Video control buttons (p. 21) p STOP (stop) 0 REW (rewind) ( PLAY (playback) ) FF (fastforward) P PAUSE (pause) r REC (recording) 8 Power zoom lever (p.
79 Additional information Identifying the parts !£ Viewfinder (p. 12) !¢ Speaker (p. 22) !∞ LCD screen (p. 16) !§ LCD BRIGHT buttons (p. 16) !¶ OPEN button (p. 15) !• VOLUME buttons (p. 21) !ª Lithium battery compartment (p. 60) @º Hook for shoulder strap (p.
80 Identifying the parts @ª COUNTER RESET button (p. 13) #º TIME button (p. 50) #¡ DATE button (p. 50) #™ DISPLAY button (p. 22) #£ TITLE button (p. 47) #¢ END SEARCH button (p. 24) #∞ PICTURE EFFECT button (p. 44) #§ START/STOP MODE switch (p.
81 Additional information Identifying the parts $£ Eyecup RELEASE knob (CCD-TRV75/ TRV85/TRV715/TRV815 only) (p. 69) $¢ EJECT switch (p. 10) $∞ LANC l control jack l stands for Local Application Control Bus System. The l control jack is used for controlling the tape transport of video equipment and peripherals connected to it.
82 Identifying the parts %¢ Built-in light (CCD-TRV93 only) (p. 52) %∞ LIGHT switch (CCD-TRV93 only) (p. 52) %§ MIC jack (PLUG IN POWER) Connect an external microphone (not supplied). This jack also accepts a “plug-in-power” microphone. %¶ Camera recording/battery lamp (p.
83 Additional information 5 1 2 3 4 Remote Commander The buttons that have the same name on the Remote Commander as on the camcorder function identically. Identifying the parts 1 Transmitter Point toward the remote sensor to control the camcorder after turning on the camcorder.
84 To prepare the Remote Commander Insert two size AA (R6) batteries by matching the + and – on the batteries to the diagram inside the battery compartment. Note on battery life The batteries for the Remote Commander last about 6 months under normal operation.
85 Additional information Operation indicators Identifying the parts Viewfinder Display window 1 Recording mode indicator (p. 29) / Mirror mode indicator (p. 17) 2 Playing back or recording in Hi8 format (p. 63) 3 Remaining battery time indicator 4 Exposure indicator (p.
86 W ar ning indicators If indicators flash in the viewfinder or in the display window, check the following: ≥≥ ... :you can hear the beep sound when the BEEP is set to ON. 123 456 78 9 JUL 4 1998 5min 0min CLEANING CASSETTE C:31:10 C:21:00 0 COPY INHIBIT 1 The battery is weak or dead.
87 Additional information Index A, B Ajusting viewfinder .............. 12 AFM HiFi Sound .............. 32, 63 ANTI GROUND SHOOTING ............................................... 15 Auto focus ............................... 42 Backlight ...........
Sony Corporation Printed in Japan.
Een belangrijk punt na aankoop van elk apparaat Sony TRV93 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sony TRV93 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sony TRV93 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sony TRV93 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sony TRV93 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sony TRV93 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sony TRV93 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sony TRV93 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
