Gebruiksaanwijzing /service van het product WO-01 van de fabrikant Smeg
Ga naar pagina of 23
INSTALLATION, USER AND MAINTENANCE MANUAL FOR WATER OSMOSIS UNIT WO-01.
.
- 29 - EQUIPMENT FOR POTABLE WATER TREATMENT CONTENTS: P a r a g r a p h GENERAL WARNINGS................................................................................................................. TECHNICAL CHARACTER ISTICS .....................
- 30 - 1. General warnings STORAGE: THE PACKED APPLIANCE MUST BE STORED IN A DRY, CONDENSATION-FREE AREA, UNDER COVER. THE ADMITTED STO R AGE TEMPERATURE IS 4-50°C. ALWAYS DISCONNE CT ELECTRICAL POWER BEFORE WORKING ON THE APPLIANCE OR DISASSEMBLING IT.
- 31 - 2. Technical characteristics Dimensions Height 814 mm Empty weight 60 kg Width 376 mm Empty weight including packagi ng 67 kg Depth 600 mm Installation chara cteri st ics Pow er cab le 3x1 length 1.5 m Di ame ter of was te di sch arg e p ip e 4 mm Plug Schuko Length of waste discharge pipe 1.
- 32 - Technical chara ct eri stics Single phase power voltage 230 v Frequency 50 Hz Osmosis pump power ratin g 450 w Delivery pump power rating 300 w Min/max water supply pressure 150-600 (1.5-6) kPa (bar) Max osmosis-treated water output 150 l/h Max water supply temperature 30 °C Max water supply hardnes s 40 °F Max water supply conductivity 2.
- 33 - 3. Positioning and installation Positioning: Before installing the appliance, check that there is su ffi cient clearance for easy extraction of consum ables and for servicing the unit. Check that there is a power socket in the vicinity of the unit.
- 34 - Water circuit and electrical hookup diagram Installing the membranes Open the front door to access the membrane housi ngs, which must be kept in their original packaging until the machine is st.
- 35 - Pressurizing and starting up the unit: After all pipes have been connected, pressurise the system gradually and check for leaks. Turn the “Osmosis pump” switch to “ I ”. Check that the following message displays: In normal operation the value Rj varies during osmosis-treated wate r prod uction.
- 36 - 4. Maintenance The osmosis treatment unit runs com pletely automatically and maintenance is minimal. The only essential operation is periodic replacement of the filter cartridges. IMPORTANT Replace the pre-filter every 3000 hours of operation and AT LEAST 1 time a year .
- 37 - Special adjustments: RECIRCULATION Recirculation retreats the wa ste water to reduce the amount of water rejected. Turn the needle valve “Recirculation” to retreat the waste water, thus reducing overall wa ter consumption. Important! Make sure, when making adjustments, that the press ure gauge reading nev er exceeds 10 -11 bar.
- 38 - 5. Plumbing diagram.
- 39 - LEGEND HYDRAULIC DI AGRAM IN Water inlet F 1 Product flow meter E 1 Filler solenoid valve P 2 Delivery minimum pressure switch P 1 Filler pressure switch R Vat cock FIL Filter - CA RBONLOK 5 mi.
- 40 - 6. Wiring diagram.
- 41 - Electrical specifications: Power supply: 230v AC 50/60Hz Max motor outlet load: 16A_ at 230V AC Max load on solenoid valve 1 outlet: 1A_ at 230v AC Max load on solenoid valve 2 outlet: 1A_ at 230V AC Instrumentation: Conductivity meter (normalised at 20°C ) scale: 0-200 uS/cm with probe K=5.
- 42 - 6- Faults Front door leds The door has two leds to indicate: - Green: power on, normal operatio n; - Red: fault, production of osmosis-treate d water stopped Important: THE DOOR GIVES NO INDICATION OF DELIVERY CIRCUIT FAULTS See below for details.
- 43 - B) Osmosis-treated water not produced Possible causes Subcause Solution Display alarm message Check power supply and power switch ON (see “Positioning and installation”) No electrical power.
- 44 - C) Water production not conforming Display alarm message Cause of alarm Solution Adjust "bypass" needle valve HHHH The treated water does not conform with settings Replace membrane s .
- 45 - Fig.3 Non-return valve Fig.4 Vat cock Fig.5 Pressure switch Solenoid valve Filter.
- 46 - 7. Electronic circuit board and programming Hold down F1 and press ENTER to enter conductivity programmi ng. We can now read the calibrated value.
- 47 - In standby (system not running) : Pressing F1 runs a water flushing cycle. X.X indicates the software version (e.g. 2.1) Display: After a few minutes, switch off and on again with the osmosis pump switch.
- 48 - Press ENTER or F1 : Stop motore se in moto per … (Stop motor after …) The following two messages concern the osmo si s pump motor condition. Set = 0 to exclude this mode; if the value is not 0, the motor stops running after having run continuously for the set period, then starts agai n.
- 49 - Press ENTER or F1 ; the system returns to standby. The sw it ch at the top of the display, if pressed to the right, switches from the waste wa ter flow display to the osmo si s-treated water flow displa y. When it is released, the display returns to waste water flow mode.
Een belangrijk punt na aankoop van elk apparaat Smeg WO-01 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Smeg WO-01 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Smeg WO-01 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Smeg WO-01 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Smeg WO-01 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Smeg WO-01 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Smeg WO-01 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Smeg WO-01 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
