Gebruiksaanwijzing /service van het product R8C/Tiny Series van de fabrikant Renesas
Ga naar pagina of 27
REG10J0049-0200 Renesas Starter Kit for R8C/2D User’s Manual RENESAS SINGLE-CHIP MICROCOMPUTER M16C F AMIL Y / R8C/T iny SERIES Rev .2.00 Renesas Solutions Corp.
Table of Contents Chapter 1. Preface .................................................................................................................................................. 1 Chapter 2. Purpose ..............................................
Chapter 1. Preface Cautions This document may be, wholly or partially, subject to change without notice. All rights reserved. Duplication of this document, either in w hole or part is prohibited without the written permission of Rene sas Solutions Corporation.
Chapter 2. Purpose This Renesas Starter Kit is an evaluati on tool for Renesas microcontrollers. Features include: • Renesas Microcontroller Programming. • User Code Debugging. • User Circuitry such as Switches, LEDs and potentiometer(s). • User or Example Application.
Chapter 3. Power Supply 3.1. Requirements This Renesas Starter Kit operates from a 3V to 5V power supply. A diode provides reverse polarity protection only if a current limiting power supply is used. All Renesas Starter Kit boards are supplied with an E8a debugger.
Chapter 4. Board Layout 4.1. Component Layout The following diagram shows the top layer component layout of the board. JA6 MCU Reset Switch E8 Header User Switches Potentiometer User LED Power LED Boo.
4.2. Board Dimensions The following diagram gives the board dimensions and connector positions. All through hole connect ors are on a common 0.1” grid for easy interfacing. MC U RING SW 1 SW 2 SW 3 R E S 120.00mm 100.00mm E8 Short Board = 85 mm 35.56 m m Serial D9 SKT 115.
Chapter 5. Block Diagram Figure 5-1 is representative of the CPU board components and their connectivity. Boot mode pins BOOT Circuitry D-type Latch RESET pin RES SW1 BOOT SW2 SW3 Switches IRQ pins PO.
Chapter 6. User Circuitry 6.1. Switches There are four switches located on the board. The f unction of each switch and its connection are shown in Table 6-1 . Switch Function Microcontroller RES When pressed, the board microcontroller is reset. RESETn Pin9 SW1/BOOT* Connects to an IRQ input for user controls.
6.4. Serial port This RSK provides two serial ports to the user. The serial por t 1 has already been configured for use. To use serial port 2 the user needs to configure the option links as given in Table 6-3 . Description Fit for RS232 TxD2 R34 RxD2 R33 Table 6-3: Serial Port settings 6.
6.6. Option Links Table 6-5 below describes the function of the option links associated with Power configuration. The default configu ration is indicated by BOLD text.
Table 6-7 below describes the function of the option links associated with serial configuration. The default configuration is indicat ed by BOLD text. Option Link Settings Reference Function Fitted Alte rnati ve (Rem oved) Related To R11 Serial Port Configuration Connects serial port TXD1 to S ERIAL D-type connect or.
Table 6-9 below describes the function of the option links associated with serial configuration. The default configuration is indicat ed by BOLD text. Option Link Settings Reference Function Fitted Al.
The Reset circuit operates by latching the state of the boot sw itch on pressing the reset button. This control is subsequently used to modify the mode pin states as required. The MODE pin should change state only while the reset signal is acti ve to avoid possible device damage.
Chapter 7. Modes This Renesas Starter Kit supports Boot mode and Single chip mode. Details of programming the FLASH memory is described in the R8C/2C Group, R8C/2D Group Hardware Manual.
Chapter 8. Programming Methods The board is intended for use with High-performance Embedded Wo rkshop and the supplied E8a debugger. Refer to R8C/2C Group, R8C/2D Group Hardware Manu al for details of pr ogra mming the microcontroller without using these tools.
Chapter 9. Headers 9.1. Microcontroller Headers Table 9- 1 to Table 9-4 show the microcontroller pin headers and their corresponding microcontroller connections. The header pins connect directly to the microcontroller pins. * Marked pins are subject to option links.
J3 Pin Circuit Net Name Device Pin Pin Circuit Net Name Device Pin 1 DLCD5 41 2 DLCD4 42 3 LED0 43 4 INT0n 44 5 TXD1 45 6 RXD1_INT3n* 46 7 CLK2 47 8 RXD2 48 9 TXD2 49 10 TMR1 50 11 TMR0 51 12 INT1n 52.
9.2. Application Headers Table 9-5 to Table 9-8 below show the standard application header connections. * Marked pins are subject to option links. JA1 Pin Header Na me Circuit Net Name Device Pin Pin .
JA5 Pin Generic Header Name CPU board Signal Name Device Pin Pin Generic Header Name CPU board Signal Name Device Pin 1 AD4 AN4 69 2 AD5 AN5 68 3 AD6 AN6 67 4 AD7 AN7 66 5 CAN1TX --- --- 6 CAN1RX --- .
Table 9-9 below shows the LIN header connections . J5 Pin Fu nction Signal Name 1 Power Supply (for LIN module) VBAT 2 GROUND GND LIN Pin Fu nction Signal Name 1 Power Supply (for LIN module) VBAT 2 L.
Chapter 10. Code Development 10.1. Overview Note: For all code debugging using Renesas software tools, the R enesas Starter Kit board must be connected to a PC USB port via an E8a.
10.4. Memory Map SFR Internal RAM Internal ROM (Data Area ) Internal ROM ( Program Area ) 00000h 002FFh 00400 h 00 FFFh 02400 h 02 BFFh 04000h Fixed Vector Tables 0FFFFh 0FFDCh Reserved area Reserved .
Chapter 11. Component Placement Figure 11-1 : Component Placement 22.
Chapter 12. Additional Information For details on how to use High-performance Embedded Workshop, refer to the High-performance Embedded Workshop manual available on the CD or from the web site. For information about the R8C/2D group microcontrollers, re fer to the R8C/2C Gro up, R8C/2D Group Hardware Manual.
Renesas S tarter Kit for R8C/2D User's Ma nual Publication Date Rev.2.00 12.OCT.2007 Published by: Renesas Solutions Cor p. Dukes Meadow, Millboard Road, Bourne End Buckinghamshire SL8 5FH, United Kingdom ©2007 Renesas Solu tions Corp., Re nesas T echnology Europe Ltd.
Renesas S tarter Kit for R8C/2D User's Manual Renesas Solutions Cor p. Dukes Meadow , Millboard Road, Bourne End Buckingham shi re SL8 5FH, United Kingdom.
Een belangrijk punt na aankoop van elk apparaat Renesas R8C/Tiny Series (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Renesas R8C/Tiny Series heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Renesas R8C/Tiny Series vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Renesas R8C/Tiny Series leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Renesas R8C/Tiny Series krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Renesas R8C/Tiny Series bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Renesas R8C/Tiny Series kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Renesas R8C/Tiny Series . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
