Gebruiksaanwijzing /service van het product 5077B van de fabrikant Makita
Ga naar pagina of 15
185 mm (744”) MODEL 5077B Equlpped wlth Electric Blade Brake Blade diameter 185 mm (7-1/4”) INSTRUCTION MANUAL Max. cutting capacity No load speed Overall length Net weight 62 mm (2-318”) 4,300 Rimin.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following: READ ALL INSTRUCTIONS. 1. 2.
17. Extension cords. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user, as well as damage the tool.
ADDITIONAL SAFETY RULES 1. Keep Guards In Place and In Working Order. Never wedge or tie lower guard open. Check operation of lower guard be- fore each use. Don’t use if lower guard does not close briskly over saw blade. CAUTION: If saw is dropped, lower guard may be bent, restricting full return.
NEVER place your hand or fingers behind the saw. If kickback occurs, the saw could easily jump back- wards over your hand, possibly causing severe injury. Fig. 7. Lower Guard. Raise lower guard with the retracting handle. 8. Adjustments. Before cutting be sure depth and bevel adjustments are tight.
12. Place the wider portion of the saw base on that part of the workpiece which is solidly supported, not on the section that will fall off when the cut is made. As examples, Fig. 5 illustrates the RIGHT way to cut off the end of a board, and Fig. 6 the WRONG way.
Removing or installing saw blade CAUTION : Always be sure that the tool is switched off and unplugged before removing or installing the blade. To remove the blade, press the shaft lock so that the blade cannot revolve and use the wrench to loosen the hex bolt clock- wise.
Adjusting depth of cut Loosen the lever on the depth guide and move the base up or down. At the desired depth of cut, secure the base by tightening the lever. Fig. 1 CAUTION : Use a shallow depth of cut when cutting thin workpiece for cleaner, safer cuts.
Switch action To start the tool, simply pull the trigger. Release the trigger to stop. CAUTION : Before plugging in the tool, always check to see that the trigger switch actuates pro- perly and returns to the "OFF" position when released. Operation Grasp the rear handle with your right hand, the front grip with your left.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark.
OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center. Service centers are listed on the warranty card packed with your tool. CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual.
May-26-'87 US 185 mm (7-1/4") HYPOID SAW Model 5077B Note The switch, noise suppressor and other part conftguratlons may differ from country to country.
MODEL 50778 'iLM & DESCRIPTION May-26-'87 US 'iLM At., DESCRIPTION MACHINE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 36 37 38 39 40 1.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
Een belangrijk punt na aankoop van elk apparaat Makita 5077B (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Makita 5077B heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Makita 5077B vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Makita 5077B leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Makita 5077B krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Makita 5077B bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Makita 5077B kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Makita 5077B . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.