Gebruiksaanwijzing /service van het product 4304 van de fabrikant Makita
Ga naar pagina of 20
Jig Saw Model 4304 4305 MODEL 4304 MODEL 4305 Variable Speed Variable Speed Length Max. cutting capacities Strokes Overall Net of stroke Wood Mild steel Aluminum per minute length weight 249 mm (9-314") 2.
GENERAL SAFETY RULES (For All Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS READ ALL INSTRUCTIONS. 1. Keep your work area clean and well lit.
11. Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. 12. Remove adjusting keys or switches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.
ADDITIONAL SAFETY RULES 1. Avoid cutting nails. Inspect for and remove all nails from the workpiece before 2. Don't cut hollow pipe. 3. Do not cut oversize workpiece. 4. Check for the proper clearance beneath the workpiece before cutting so that 5.
The followings show the symbols used for tool. v ................................. volts A ................................. amperes Hz ................................. herts kg ................................. kilograms h ..........................
Installing or removing the saw blade CAUTION: Always be sure that the tool is switched off and unplugged before installing or removing the blade. To install the blade, loosen the screw on With the blade teeth facing forward, insert 1 the blade into the blade holder as far as it will go.
Installing the universal shank jig saw blade CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the blade. If the universal blade clamp is used, you can use blades of other makes which have a universal shank like the one shown in the figure, with a blade width of 6.
Position Cutting action Applications I ~~~ ~~~~ ~ ~ ~ ~ ~~~ I I I Smallorbit cutting action 1 For cutting mild steel, aluminum and hard wood. straight line cutting action 0 For cutting mild steel, stainless steel and plastics. For clean cuts in wood and plywood.
Speed adjusting dial The tool speed can be adjusted and maintained between 500 and 3,000 strokes per minute by turning the adjusting dial. The dial is marked 1 (lowest speed) to 6 (full speed). Workpiece to be cut 1- Lock lever :or 4304 Number on adjusting dial Refer to the table at right to select the proper speed for the workpiece to be cut.
CAUTION : Always hold the tool with the base flush with the workpiece. Failure to do so may cause *Advance the tool very slowly when cutting curves or scrolling. Forcing the tool may a slanted cutting surface and blade breakage. cause a slanted cutting surface and blade breakage.
cutouts Cutouts can be made with either of two methods A or B. A) Boring a starting hole: For internal cutouts without a lead-in cut from an edge, predrill starting hole more than 12 mm (15/32") in diameter. Insert the blade into this hole and hold the tool firmly against the workpiece to start your cut.
Finishing edges To trim edges or make slight dimensional adjustments, run the blade lightly along the cut edges. 'Of I For 4305 Metal cutting Always use a suitable coolant (cutting oil) when cutting metal. Failure to do so will cause significant blade wear.
Guide rule (rip fence; optional accessory) When cutting widths of under 150 mm (5-29/32") repeatedly, use of the guide rule will assure fast, clean, straight cuts. To install it, loosen the bolt on the front of the base. Slip in the guide rule and secure the bolt.
To attach the vacuum head on the tool, insert the hook of the vacuum head into the hole in the base. Tighten the bolt to secure the vacuum head. Then connect a Makita vacuum cleaner to the vacuum head.
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner.
Jig saw blade Blade type No. 51 Application ' Wood and plywood Plastics Aluminum 1.5 - 3 mm thick 1 - 6 mm thick - 11/16" - 118") 13/64' - 1/4'l H 4 - 60 mm thick 4 - 60 mm thick NO. 58 I 15/32" - 2-3/6"1 15/32" - 2-318") I- Is No.
JIG SAW Model 4304 Note: The switch, noise suppressor and other part configurations may differ from country to country. 17.
MACHINE ~ 1 1 Switch 2 1 Handle Set IWith Item 551 3 1 Tapping Screw Flange PT 4x20 4 1 Cord 5 1 Cord Guard 6 1 Strain Relief 7 2 Tapping screw 4xia 9 1 PI" 3 10 1 Switch Lever 11 1 Spacer 12 1 C.
JIG SAW Model 4305 Note: The switch, noise suppressor and other part configurations may differ from country to country. 19.
MAKlTA LIMrrED ONE YEAR WARRANTY I Warranty Policy Every Makita tool is thorou ly inspezted and tested before leaving the factory. It is warranted to be free of defects from wor&kp and materials for the period of ONE YEAR from the date of original purchrsc.
Een belangrijk punt na aankoop van elk apparaat Makita 4304 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Makita 4304 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Makita 4304 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Makita 4304 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Makita 4304 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Makita 4304 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Makita 4304 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Makita 4304 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.