Gebruiksaanwijzing /service van het product CCZ130AT van de fabrikant Magnavox
Ga naar pagina of 52
Owner’s Manual Important! Return your Warranty Registration Card within 10 days. See why inside. Color TV with built-in VCR CCZ130AT Use photograph (same as carton) CCZ130comb 4/5/99 7:31 PM Page 1.
Once your PHILIPS MAGNAVOX purchase is registered, you’re eligible to receive all the privileges of owning a PHILIPS MAGNAVOX product. So complete and return the Warranty Registration Card enclosed with your purchase at once. And take advantage of these important benefits.
Introduction 3 • Before doing anything else, record the TV/VCR’s model and serial num- bers in the spaces provided on page two. These numbers will help us assist you if you ever call for help.
4 Table of Contents Setting Up Your TV/VCR Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• The remote control and its batteries are supplied. • Do not mix alkaline and man- ganese batteries. • Do not mix old and new batteries. Before Using the TV/VCR 5 Putting Batteries in the Remote Control 1 Remove the battery compartment lid on the bottom of the remote control by sliding it in the direction of the arrow.
6 Hooking Up The TV/VCR ANT. ANT. Hooking Up Your TV/VCR With a Cable Signal or Outdoor Antenna ANT. IN OUT ANT. Connect an RF coaxial cable (75- ohm, not supplied) to the OUT Jack on the Cable Box and to the ANT(enna) Jack on the TV/VCR. Connect a Cable signal or an antenna to the ANT(enna) Jack.
Hooking Up The TV/VCR (cont’d) 7 EARPHONE AUDIO VIDEO STOP/EJECT REW PLAY F.FWD REC/OTR CHANNEL VOLUME POWER OUT IN VIDEO IN OUT 3CH 4CH AUDIO ANT. OUT IN VIDEO IN OUT 3CH 4CH AUDIO ANT. VIDEO AUDIO • Before connecting an antenna or cable signal to the ANT(enna) Jack, make sure the pin is not bent.
8 Turning On the TV/VCR Before you turn on the TV/VCR, make sure there are batteries in the remote control and the TV/VCR is hooked up correctly. The instructions on this page work only when you turn on the TV/VCR for the first time. 1 Press the POWER button.
Language Selection 9 Follow the steps below to change the language of the on-screen displays. 3 Press the PLAY/ ▲ button or the STOP/ ▼ button to choose SELECT LANGUAGE. Then, press the FF/SEARCH B button. 4 Press the PLAY/ ▲ button or the STOP/ ▼ button to select ENGLISH or ESPAÑOL (Spanish).
10 Automatic Channel Setup Although the TV/VCR may automatically memorize the channels you receive when you turn it on for the first time, you may set up channels again by following the steps below. 1 Press the MENU button. TO ADJUST PRESS { / B > INPUT EXIT PRIM.
Automatic Channel Setup (cont’d) 11 4 Press the FF/SEARCH B button or the REW(ind)/SEARCH { button to select SAVED (to add that channel) or DELETED (to delete that channel). 5 Press the STATUS/EXIT button. Programming of the channel you added or deleted will appear.
12 Setting the Clock • Entries that do not match the TV/VCR’s calendar will cause a question mark (?) to appear on the screen. • To make corrections while you are setting the clock, press the CLEAR button until the space for the num- ber you want to correct is flashing.
Setting the Clock (cont’d) 13 5 Press two Number buttons for the hour(s) and two Number buttons for the minute(s). Then press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.
14 Setting the Clock (cont’d) Automatic PBS Channel Selection 4 If ON appears beside AUTO CLOCK, press the MENU button. If OFF appears beside AUTO CLOCK, press the FF/SEARCH B button so that ON appears to the right of AUTO CLOCK, then press the MENU button.
Setting the Clock (cont’d) 15 7 When the TV/VCR finds the PBS channel, the time will appear on-screen. Press the STATUS/EXIT button. 6 NOW SEARCHING flashes on the TV/VCR screen. However, you may see the message: “PLEASE TURN OFF TO SET AUTO CLOCK PLEASE WAIT SEVERAL MINUTES.
16 Setting the Clock (cont’d) Manual PBS Channel Selection 4 If ON appears beside AUTO CLOCK, press the MENU button. If OFF appears beside AUTO CLOCK, press the FF/SEARCH B button so that ON appears to the right of AUTO CLOCK, then press the MENU button.
Setting the Clock (cont’d) 17 8 When the TV/VCR finds the clock data, the time will appear on-screen. Press the STATUS/EXIT button. 6 Use the Number buttons to select your PBS station. If you make a mistake, press the CLEAR button, then enter the correct number.
18 Daylight-Saving Time 4 Press the PLAY/ ▲ button or the STOP/ ▼ button to select DAYLIGHT SVG.TIME. Then, press the FF/SEARCH B button so that ON or OFF appears beside DAYLIGHT SVG. TIME (Daylight Saving Time). 5 Press the STATUS/EXIT button. 1 Press the MENU button.
Time Zone 19 When you set the clock using AUTO CLOCK, specify a time zone in which a local PBS channel is located. The TV/VCR will maintain the clock according to your time zone. • If you select AUTO at step 5, the TV/VCR will set the clock according to the time zone data of the PBS station it finds.
20 Front Panel EARPHONE AUDIO VIDEO STOP/EJECT REW PLAY F.FWD REC/OTR CHANNEL VOLUME POWER Cassette Compartment Insert a video cassette tape here. POWER Button Press to turn the power on or off.
Rear Panel 21 ANT. ANT(enna) Jack Connect your antenna or cable here. Details are on pages six - seven. Antenna Hole Connect the stem of an indoor antenna here. Details are on page six. AC Power Cord Connect to a standard AC outlet to supply power to the TV/VCR.
22 Remote Control Buttons STOP/ ▼ Button Press to stop the tape. Press to select an item in the on-screen menu. PAUSE/STILL Button During recording, press to temporarily stop the recording. Press again to resume recording. Details are on page 29. You cannot pause a One-Touch Recording.
Remote Control Buttons (cont’d) 23 FF/SEARCH B Button When tape playback is stopped, press to fast forward the tape at high speed. During tape playback, press to fast forward the tape while the picture stays on-screen. Details are on page 46. Press to change the setting of an item in the on-screen menu or press to proceed to the next menu.
TO ADJUST PRESS { / B 24 Adjusting the Picture Controls Follow these steps to adjust the TV/VCR’s brightness, picture, color, tint, and sharpness. 1 Press the MENU button. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select the desired control (BRIGHTNESS, for example).
Adjusting the Picture Controls (cont’d) 25 Decrease Increase BRIGHTNESS decreased brightness increased brightness PICTURE decreased contrast increased contrast COLOR paler more brilliant TINT more purple more green SHARPNESS softer clearer Press the REW(ind)/SEARCH { button to decrease a picture control.
• If the channel you select has no broadcast, the screen will be solid blue. • You cannot view closed captions during recording or tape playback if COUNTER ONLY is set to ON.
Reminder 27 The channel number will remain on-screen at all times when you set REMINDER to ON in the pop up menu. The exception is dur- ing tape playback, Forward and Reverse Searching and Still modes, and when closed captioning is selected (CAPTION in the pop up menu).
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ +100 ALT.CH MENU MEMORY 28 Playing • If the tape you want to play is already in the TV/VCR, turn on the TV/VCR power, then press the PLAY/ ▲ button.
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ +100 ALT.CH MENU MEMORY Recording 29 • You cannot record one channel while watching another. • Recording options are on pages 30 - 36.
30 One-Touch Recording The One-Touch Recording (OTR) function allows you to program an immediate timed recording from 30 minutes to eight hours long without setting the timer. Before you begin, make sure: ● Channels are set up. ● There is a tape in the TV/VCR.
Rerecording (Tape Duplication) 31 • Unauthorized recording of copy- righted television programs, video tapes, or other materials may infringe on the rights of copyright owners and violate copyright laws. • Different brands of equipment may operate differently.
32 Timer Recording Follow the steps below to program the TV/VCR to record TV programs while you’re away from home. The TV/VCR will turn itself on, record, and turn itself off automatically. Before you begin, make sure: ● The clock is set. If not, CLOCK MUST BE SET appears.
ONE TIME PROGRAM PROGRAM 1 CHANNEL – – TO CORRECT PRESS CLEAR TO END PRESS EXIT Timer Recording (cont’d) 33 5 ● Enter the channel of the TV program you want to record (you must enter a 0 before all single-digit channels). ● If you are recording from line input, press 0, 0.
34 Timer Recording (cont’d) The TV/VCR must be off for a timer record- ing! Make sure there is a tape in the TV/VCR. 8 Press the Number 1 button to record in SP speed, press the Number 2 button to record in LP speed, or press the Number 3 button to record in SLP speed.
Timer Recording (cont’d) 35 6 Repeat steps 1 - 4 to make sure you have cleared the correct position. Checking or Clearing Timer Recordings 1 With the TV/VCR on, press the MENU button. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select VCR PROGRAM, then press the FF/SEARCH B button.
36 Defeat Recording Follow the steps below to prevent accidental recording. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select VCR SETUP, then press the FF/SEARCH B button. 3 Press the PLAY/ ▲ button or the STOP/ ▼ button to select RECORD DEFEAT, then press the FF/SEARCH B button so that ON appears beside RECORD DEFEAT.
Setting the Sleep Timer 37 Use the sleep timer to program the TV/VCR to shut off in a cer- tain amount of time. 1 Press the SLEEP button. The sleep timer display will appear on-screen. (You can not set the sleep timer during a recording.) 1-2 • Finish all recordings before the TV/VCR shuts itself off.
When you watch a program that is being broadcast with closed captions, you can access on-screen boxes containing the pro- gram’s dialogue (for example, what a character is saying), dialogue in a foreign language, or information (such as a channel guide, schedule, or announcements).
Closed Caption (cont’d) 39 • You cannot view closed captions during recording or tape playback if COUNTER ONLY is set to ON. • Abbreviations, symbols, and other grammatical shortcuts are often used in order to keep pace with the on-screen action.
Usually, the volume bar appears when you press the VOLUME o / p buttons. If you do not need it, set the VOLUME BAR to OFF position. For example, when you watch a program that is being broadcast with closed captions, you may choose to set the VOLUME BAR to OFF so the captions can remain on-screen.
Repeat Play 41 Follow the steps below to program the TV/VCR to play a tape over and over. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select VCR SETUP, then press the FF/SEARCH B button. 3 Press the PLAY/ ▲ button or the STOP/ ▼ button to select REPEAT PLAY, then press the FF/SEARCH B button so that ON appears beside REPEAT PLAY.
42 A - B Repeat Play • To cancel A-B Repeat Play, set ONE TIME PLAY to ON. To set ONE TIME PLAY to ON, follow steps 1 - 3 above. Then, press the PLAY/ o button or the STOP/ p button to select ONE TIME PLAY. Press the FF/SEARCH B button so that ON appears beside ONE TIME PLAY.
6 Press the STATUS/EXIT button to remove the display. A- B REPEAT will appear on-screen. Beneath it, the letter A will flash beside the real-time counter. . A-B REPEAT A 0:12:34 7 Play, fast forward, or rewind the tape to the position at which you want to begin playback.
44 Real-Time Counter Memory Follow the steps below to reset the real-time counter to zero at a tape location you want to refer to later. 1 Play, fast forward, or rewind a tape to the location that you would like to refer to later. Stop the tape. 2 Press the STATUS/EXIT button.
Automatic Operation Features 45 The following playback features will always operate. Automatic Playback When you put a tape in the TV/VCR, the power will come on automatically.
46 Playback Options Forward and Reverse Searching (SP/LP/SLP) 1 During tape playback, press and release the FF/SEARCH B button or the REW(ind)/SEARCH { button. A fast forward or reverse picture search will begin. 2 To return to normal playback, press the PLAY/ ▲ button.
Specifications General CRT: 13-inch in line gun Television system: NTSC-M Closed caption system: Section 15.119, FCC (Federal Communications Commission) Standard Video Heads: Two heads Tape width: 1/2 inch (12.65 mm) Tape speed SP: 33.35 mm/sec. LP: 16.
48 Helpful Hints Location For safe operation and satisfactory performance of your TV/VCR, remember the following: • Shield it from direct sunlight and keep it away from sources of intense heat. • Avoid dusty or humid places. • Avoid places with insufficient ventilation.
Helpful Hints (cont’d) 49 The remote control is not available, or the remote control will not access the pop up menu. • Use the buttons on the front panel of the TV/VCR to access the pop up menu (page 20). You can not enter numbers (for example, to program a timer recording) using the front panel buttons.
50 Limited Warranty WHO IS COVERED? You must have proof of purchase to receive warranty service. A sales receipt or other document showing that you purchased the product is considered proof of purchase. WHAT IS COVERED? Warranty coverage begins the day you buy your product.
a-b repeat play . . . . . . . .42 - 43 accessories . . . . . . . . . . . . . . .52 ant(enna) jack . . . . . . . . . . .6, 21 audio jack . . . . . . . . . . .7, 20, 31 automatic playback . . . . . . . . . . . . . . .45 rewind . . . . . . . . . . . . . .
IB8025E001 Printed In Malaysia 0EMN01366 / B5913UP * * * * * S UPPLIED A CCESSORIES Remote Control (4835 218 37222) Two AA Batteries (4835 138 17012) Check to be sure the items on this page are packed with your TV/VCR. These accessories are provided to help you use or set up your TV/VCR.
Een belangrijk punt na aankoop van elk apparaat Magnavox CCZ130AT (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Magnavox CCZ130AT heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Magnavox CCZ130AT vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Magnavox CCZ130AT leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Magnavox CCZ130AT krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Magnavox CCZ130AT bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Magnavox CCZ130AT kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Magnavox CCZ130AT . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
