Gebruiksaanwijzing /service van het product CCB130CN van de fabrikant Magnavox
Ga naar pagina of 60
Owner’s Manual Important! Return your Warranty Registration Card within 10 days. See why inside. Color TV with built-in VCR CCB130CN CCB190CN.
Once your PHILIPS purchase is registered, you’re eligible to receive all the privileges of owning a PHILIPS product. So complete and return the Warranty Registration Card enclosed with your purchase at once. And take advantage of these important benefits.
Introduction 3 • Before doing anything else, record the TV/VCR’s model and serial num- bers in the spaces provided on page two. These numbers will help us assist you if you ever call for help. • Your new product, its packaging, and this manual contain materials that can be recycled and reused.
4 Table of Contents Setting Up Your TV/VCR Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• The remote control and its batteries are supplied. • Do not mix alkaline and man- ganese batteries. • Do not mix old and new batteries. Before Using the TV/VCR 5 Putting Batteries in the Remote Control 1 Remove the battery compartment lid on the bottom of the remote control by sliding it in the direction of the arrow.
6 Hooking Up the TV/VCR ANT. ANT. Hooking Up Your TV/VCR With a Cable Signal or Outdoor Antenna ANT. IN OUT ANT. Connect an RF coaxial cable (75- ohm, not supplied) to the OUT Jack on the Cable Box and to the ANT(enna) Jack on the TV/VCR. Connect a Cable signal or an antenna to the ANT(enna) Jack.
Hooking Up the TV/VCR (cont’d) 7 AUDIO VIDEO STOP EJECT REW PLAY F .FWD REC OTR CHANNEL VOLUME POWER EARPHONE OUT IN VIDEO IN OUT 3CH 4CH AUDIO ANT. OUT IN VIDEO IN OUT 3CH 4CH AUDIO ANT. VIDEO AUDIO • Before connecting an antenna or cable signal to the ANT(enna) Jack, make sure the pin is not bent.
8 Turning On the TV/VCR Before you turn on the TV/VCR, make sure batteries are in the remote control and the TV/VCR is hooked up correctly. The instructions on this page work only when you turn on the TV/VCR for the first time. 1 Press the POWER button.
Language Selection 9 Follow the steps below to change the language of the on-screen displays and menus. 3 Press the PLAY/ ▲ button or the STOP/ ▼ button to choose SELECT LANGUAGE. Then, press the F.FWD/ B button. 4 Press the PLAY/ ▲ button or the STOP/ ▼ button to select ENGLISH or FRANCAIS (French).
10 Automatic Channel Setup Although the TV/VCR may automatically memorize the channels you receive when you turn it on for the first time, you may set up channels again by following the steps below. 1 Press the MENU button. 3 Press the PLAY/ ▲ button or the STOP/ ▼ button to select PRIM.
Automatic Channel Setup (cont’d) 11 4 Press the F.FWD/ B button or the REW(ind)/ { button to select SAVED (to add that channel) or DELETED (to delete that channel). Repeat steps 3-4 to add or delete other channels. 5 Press the STATUS/EXIT button. Programming of the channel you added or deleted will appear.
12 Setting the Clock • Entries that do not match the TV/VCR’s calendar will cause a question mark (?) to appear on the screen. • To make corrections while you are setting the clock, press the CLEAR button until the space for the num- ber you want to correct is flashing.
Setting the Clock (cont’d) 13 5 Press two Number buttons for the hour(s) and two Number buttons for the minute(s). Then press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.
14 Setting the Clock (cont’d) Automatic PBS Channel Selection 4 If ON appears beside AUTO CLOCK, press the MENU button. If OFF appears beside AUTO CLOCK, press the F.FWD/ B button so that ON appears to the right of AUTO CLOCK, then press the MENU button.
Setting the Clock (cont’d) 15 7 When the TV/VCR finds the PBS channel, the time will appear on the screen. Press the STATUS/EXIT button. 6 NOW SEARCHING flashes on the TV/VCR screen. ● If CANNOT FIND CLOCK DATA flashes on the TV/VCR screen, you will be prompted to turn off the TV/VCR.
16 Setting the Clock (cont’d) Manual PBS Channel Selection 4 If ON appears beside AUTO CLOCK, press the MENU button. If OFF appears beside AUTO CLOCK, press the F.FWD/ B button so that ON appears to the right of AUTO CLOCK, then press the MENU button.
Setting the Clock (cont’d) 17 8 When the TV/VCR finds the clock data, the time will appear on the screen. Press the STATUS/EXIT button. 6 Use the Number buttons to select your PBS station.
18 Daylight-Savings Time 4 Press the PLAY/ ▲ button or the STOP/ ▼ button to select DAYLIGHT SVG.TIME. Then, press the F.FWD/ B button so that ON or OFF appears beside DAYLIGHT SVG. TIME (Daylight Savings Time). 5 Press the STATUS/EXIT button. 1 Press the MENU button.
Time Zone 19 When you set the clock using AUTO CLOCK, specify your time zone. The TV/VCR will maintain the clock according to your time zone. • If you select AUTO at step 5, the TV/VCR will set the clock according to the time zone data of the PBS station it finds.
20 Front Panel AUDIO VIDEO STOP EJECT REW PLAY F .FWD REC OTR CHANNEL VOLUME POWER EARPHONE Cassette Compartment Insert a video cassette tape here. POWER Button Press to turn the power on or off.
Rear Panel 21 ANT . ANT(enna) Jack Connect your antenna or cable here. Details are on pages six-seven. Antenna Hole Connect the stem of an indoor antenna here. Details are on page six. AC Power Cord Connect to a standard AC outlet to supply power to the TV/VCR.
F.FWD/ B Button When tape playback is stopped, press to fast forward the tape at high speed. During tape playback, press to fast forward the tape while the picture stays on the screen. Details are on page 41. Press to change the setting of an item in the on-screen menu or press to proceed to the next menu.
Remote Control Buttons (cont’d) 23 CH(annel) m m / n n Button Press to scan through the TV/VCR’s channels. MEMORY Button Press to memorize a tape position at which the real-time counter was set to 0:00:00. Details are on page 40. Or, press to memorize the start and end positions on a tape when setting up A-B Repeat Play.
TO ADJUST PRESS { / B 24 Adjusting the Picture Controls Follow these steps to adjust the TV/VCR’s brightness, picture, color, tint, and sharpness. 1 Press the MENU button. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select the desired control (BRIGHTNESS, for example).
Adjusting the Picture Controls (cont’d) 25 Decrease Increase BRIGHTNESS decreased brightness increased brightness PICTURE decreased contrast increased contrast COLOR paler more brilliant TINT more purple more green SHARPNESS softer clearer Press the REW(ind)/ { button to decrease a picture control.
• You cannot view closed captions during recording or tape playback if COUNTER ONLY is set to ON. Details are on pages 49-50. Helpful Hint 1 Press the MENU button.
Reminder 27 The channel number will remain on the screen at all times when you set REMINDER to ON. The exception is when closed cap- tioning is selected. Set REMINDER to ON or OFF by following the steps below. 1 Press the MENU button. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select REMINDER.
28 Playing • If the tape you want to play is already in the TV/VCR, turn on the TV/VCR power, then press the PLAY/ ▲ button. • Playback features and options are on pages 37-41. • When you play a tape recorded in S-VHS format on this unit, you can not get the high resolution that would be available on an S-VHS VCR.
Recording 29 • You cannot record one channel while watching another. • Recording options are on pages 30-36. • You cannot record if DEFEAT RECORDING is set to ON.
30 One-Touch Recording The One-Touch Recording (OTR) function allows you to program an immediate timed recording from 30 minutes to eight hours long without setting the timer. Before you begin, make sure: ● Channels are set up. ● There is a tape in the TV/VCR.
CCB130CN Rerecording (Tape Duplication) 31 • Unauthorized recording of copy- righted television programs, video tapes, or other materials may infringe on the rights of copyright owners and violate copyright laws. • Different brands of equipment may operate differently.
32 Timer Recording Follow the steps below to program the TV/VCR to record TV programs while you’re away from home. The TV/VCR will turn itself on, record, and turn itself off automatically. Before you begin, make sure: ● The clock is set. If not, CLOCK MUST BE SET appears, fol- lowed by the SET CLOCK menu.
ONE TIME PROGRAM PROGRAM 1 CHANNEL – – – TO CORRECT PRESS CLEAR TO END PRESS EXIT Timer Recording (cont’d) 33 5 Use the Number buttons to enter the channel of the TV program you want to record. ● If you are recording from line input, press 0, 0.
34 Timer Recording (cont’d) Turn off the TV/VCR for the recording. Insert a tape in the TV/VCR. Leave the Cable Box/DBS on (if applicable). 8 Press the Number 1 button to record in SP speed or press the Number 2 button to record in SLP speed. Details about tape speed are on page 29.
Timer Recording (cont’d) 35 6 Repeat steps 1 - 4 to make sure you have cleared the cor- rect position. Checking or Clearing Timer Recordings 1 With the TV/VCR on, press the MENU button. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select VCR PROGRAM, then press the F.
36 Defeat Recording Follow the steps below to prevent accidental recording. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select VCR SETUP, then press the F.FWD/ B button. 3 Press the PLAY/ ▲ button or the STOP/ ▼ button to select DEFEAT RECORDING, then press the F.
Repeat Play 37 Follow the steps below to program the TV/VCR to play a tape over and over. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select VCR SETUP, then press the F.FWD/ B button. 3 Press the PLAY/ ▲ button or the STOP/ ▼ button to select REPEAT PLAY, then press the F.
38 A-B Repeat Play • To cancel A-B Repeat Play, set ONE TIME PLAY to ON. To set ONE TIME PLAY to ON, follow steps 2-3 above. Then, press the PLAY/ o but- ton or the STOP/ p button to select ONE TIME PLAY. Press the F.FWD/ B button so that ON appears beside ONE TIME PLAY.
6 Press the STATUS/EXIT button to remove the menu. A-B REPEAT will appear on the screen. Beneath it, the letter A will flash beside the real-time counter. . A-B REPEAT A 0:12:34 7 Play, fast forward, or rewind the tape to the position at which you want to begin playback.
40 Real-Time Counter Memory Follow the steps below to reset the real-time counter to zero at a tape location you want to refer to later. 1 Play, fast forward, or rewind a tape to the location that you would like to refer to later. Stop the tape. 2 Press the STATUS/EXIT button.
Playback Options 41 Forward and Reverse Searching (SP/LP/SLP) 1 During tape playback, press and release the F.FWD/ B button or the REW(ind)/ { button. A fast forward or reverse picture search will begin. 2 To return to normal playback, press the PLAY/ ▲ button.
42 SmartLock SmartLock enables parents to prevent their children from watch- ing inappropriate material on TV. SmartLock reads the ratings for programming (except for news and sports programs, unedite.
SmartLock (cont’d) 43 5 Press the PLAY/ ▲ button or the STOP/ ▼ button to select Movie Ratings or Parental Guidelines. Then, press the F.FWD/ B button. BLOCK > Movie Ratings Parental Guidelines SELECT KL CHOOSE B TO END PRESS EXIT 6 Press the PLAY/ ▲ button or the STOP/ ▼ button to select the rating you want to block.
To change the access code, follow these steps. 44 SmartLock (cont’d) 1 Press the MENU button. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select SMARTLOCK. Then, press the F.FWD/ B button. SMARTLOCK Enter Your Access Code > SMARTLOCK REVIEW EXIT PRIM.
SmartLock (cont’d) 45 To check the SmartLock settings, follow these steps. 1 Press the MENU button. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select REVIEW. Then, press the F.FWD/ B button so that the SmartLock settings appear. Ratings that are blocked will appear on the screen.
2 Press the PLAY/ o o button or the STOP/ p p button to select VCR SETUP, then press the F.FWD/ B B button. 46 Blue Background VOL . CH. 3 2 1 6 5 4 9 8 7 0 POWER STATUS/EXIT TRACKING REC/OTR SPEED MEMORY ALT.
1 Press the SLEEP/WAKE UP button. • To cancel the sleep timer, press the SLEEP/WAKE UP button. Press the PLAY/ o button or the STOP/ p but- ton to select SLEEP, then press the REW(ind) / s s button or the F.FWD/ B B button to select OFF. Press the STATUS/EXIT button.
48 Wake Up Timer 1 4 2-3 The Wake Up Timer turns on the TV/VCR automatically at a speci- fied time within the next 24 hours. You may set the TV/VCR to turn on at a TV channel (the channel at which the TV/VCR was set last) or with VCR playback. To set the Wake Up Timer, follow the steps below.
When you watch a program that is being broadcast with closed captions, you can access on-screen boxes containing the pro- gram’s dialogue (for example, what a character is saying), dialogue in a foreign language, or information (such as a channel guide, schedule, or announcements).
50 Closed Caption (cont’d) • You cannot view closed captions during recording or tape playback if COUNTER ONLY is set to ON. • Abbreviations, symbols, and other grammatical shortcuts are often used in order to keep pace with the on-screen action.
Usually, the volume bar appears when you press the VOL(ume) m / n button. If you do not need it, set the VOLUME BAR to OFF. For example, when you watch a program that is being broadcast with closed captions, you may choose to set the VOLUME BAR to OFF so the captions can remain on the screen.
52 Automatic Operation Features The following playback features will always operate. Automatic Playback When you put a tape in the TV/VCR, the power will come on automatically.
General CRT: 13-inch in line gun (CCB130CN) 19-inch in line gun (CCB190CN) Television system: NTSC-M Closed caption system: Section 15.119, FCC (Federal Communications Commission) Standard Video Heads: Two heads Tape width: 1/2 inch (12.65 mm) Tape speed SP: 33.
AUDIO Jack: jack located on the front of the TV/VCR which is used to record audio from another source. Automatic Channel Setup: process in which the TV/VCR scans all available channels and places the ones you receive in its memory. Then, when you push the CH(annel) o / p buttons, you only scan through channels you receive.
Helpful Hints 55 Location For safe operation and satisfactory performance of your TV/VCR, remember the following: • Shield it from direct sunlight and keep it away from sources of intense heat. • Avoid dusty or humid places. • Avoid places with insufficient ventilation.
56 Helpful Hints (cont’d) The remote control is not available, or the remote control will not access the pop up menu. • Use the buttons on the front panel of the TV/VCR to access the pop up menu. You can not enter num- bers (for example, to program a timer recording) using the front panel buttons.
Limited Warranty 57 WHO IS COVERED? You must have proof of purchase to receive war- ranty service. A sales receipt or other document showing that you purchased the product is considered proof of purchase. WHAT IS COVERED? Warranty coverage begins the day you buy your product.
a-b repeat play . . . . . . . . .38-39 accessories . . . . . . . . . . . . . . .60 ant(enna) jack . . . . . . . . . . .6, 21 audio jack . . . . . . . . . . .7, 20, 31 automatic playback . . . . . . . . . . . . . . .52 rewind . . . . . . . . . . . . . .
.
IB8217B001 Printed In Malaysia 0EMN01703 / T5113CP * * * * * S UPPLIED A CCESSORIES O PTIONAL A CCESSORIES The following items are supplied with your TV/VCR; they are provided to help you use or set up your TV/VCR. The following additional items are not provided with your TV/VCR, but they are designed for use with your new TV/VCR.
Een belangrijk punt na aankoop van elk apparaat Magnavox CCB130CN (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Magnavox CCB130CN heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Magnavox CCB130CN vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Magnavox CCB130CN leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Magnavox CCB130CN krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Magnavox CCB130CN bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Magnavox CCB130CN kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Magnavox CCB130CN . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
