Gebruiksaanwijzing /service van het product FIM400 4100 van de fabrikant Franklin Industries, L.L.C.
Ga naar pagina of 24
Automatic Commercial Ice Cube Ma chine User ’ s Manua l Franklin Industries, LLC Model FIM 400 4100 First Avenue Brooklyn, NY 11232 - 3321 Tel.: 1 - 888 - 424 - 8278 E - mail: customerservice@franklinchef.com ® Be sure ice maker has been standing upright for at least 24 hours prior to plug - in.
1 TABLE OF CONTENT S Page ICE MAKER SAFETY .................................................................................... 2 IMPORTANT SAFEGUARDS ................................................................ 2 – 4 MAJOR F EATURE S ..........
2 ICE MAKER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your a ppliance . Always read and obey all safety messages. This is the Safety Alert Symbol. This symbol alerts you to potential hazards that can injure or kill you and others.
3 ? It is recommended that a se parate circuit, serving only your ice maker, be provided. Use receptacles that cannot be turned off by a switch or pull chain. ? Do not connect or disconnect the electric plug when your hands are wet. ? Never unplug the ice maker by pulling on the power cord.
4 ? Turn on the water supply tap before switching on the ice maker. Never turn off the water supply tap when the ice m aker is working. ? Except to take ice from the storage bin , keep the bin door closed in order to reduce ice melting and to promote proper ice formation.
5 Technical Information Model: FIM 400 Electrical input: 115VAC ~ 60Hz Power consumption: 8.3 kW · h /100 lbs of ice Ice - making/Ice - harvest rated current: 12.4A/15.3A Refrigerant: R 404 a, 24. 6 oz. High/Low side pressure: 350psig/1 9 0psig Unit width x depth x height: 30 ? x 24 ? x 20.
6 Comp onent Locations T o p panel W ater distribution tube E vaporator W ater pump F loater valve W ater tank Ice - full probe I ce storage bin (available separately) A djustab le feet C ontrol p ane.
7 Ice Maker Installation Unpacking This unit is an ice maker onl y. It requires a separate ice storage bin . Remove packaging materials IMPORTANT: Do not remove any permanent instruction labels or the data label s on your ice maker.
8 REAR VIEW T he two holes are for attachment to the ice storage bin. S ee drawing s below . Typical installation of ice storage bin T wo connect ing brackets are attached to the upper rear edge of the ice storage bin. T urn the brackets up (180 ? ) and use two screws to connect the main machine and ice storage bin.
9 (38ºC). This unit MUST be installed in an area protected from the elements, such as wind, rain, water spray or drips. ? The unit should not be located next to ovens, grills or other sources of high heat. ? Installation of the ice maker requires a cold water supply inlet of 1/4 ? ( 6 , 35 mm ) soft copper tubing with a shut - off valve.
10 ordinances, is required. The ice maker should always be plugged into its own individual electrical outlet. It is re commended that a separate circuit, serving only your ice maker, be provided. Use receptacles that cannot be turned off by a switch or pull chain.
.
12 Operation Final Check List before Operation 1. Have all packing materials and tape been removed from the interior and exterior of the ice maker? 2. Did you clean the ice stor age bin? 3. Have the installation instructions been followed, including connecting the machine to water and electricity? 4.
13 I ce - making stage I ce harvest stage IMPORTANT: ? Although the unit has been tested and cleaned at the factory, due to long -term transit and storage, the first batch of cubes must be discarded. ? Never turn off the water supply tap when the ice maker is working.
14 Normal Sounds Your new ice maker ma y make sounds that are unfamiliar to you. Most of the new sounds are normal. Hard surfaces like the floor and walls can amplify the sounds. The following describes the kinds of sounds that might be new to you and what may be causing them.
15 Cleaning and Maintenance Periodic cleaning and prope r maintenance will ensure efficiency, top performance, and long life. The maintenance intervals listed are based on normal conditions. You may want to shorten the intervals if you have pets or there are other special considerations.
16 1. Disconnect power to the unit. 2. Remove the front panel of the ice maker. U n s crew the wa ter tank screw nut and drain water completely into the ice storage bin . Th e water drain s o ut through the drain hole in the bin. ( NOTE : D on ’ t forget to screw the nut back into the water tank hole again .
17 Maker Cleaner Solution into the water t ank . 4. T urn on the power switch . W ithin 3 minutes press the C lean button . T he machine will go into the cleaning mode automatically.
18 2. R emove the condenser air filter with a screwdriver. 3. Use a brush to wipe up and down the filter surface with a mild detergent solution such as 1 oz . of dishwashing liquid mixed with 2 gallons of warm water . Do not use solvent - based or abrasive cleaners.
19 5. When you want to clean the machine, turn off the power switch first, then turn it on again . P ress the C lean button within 3 minutes and the ice maker will start the clean ing mod e , with harvest and ice - making indicator s blink ing .
20 Troubleshooting Before Calling for Service If the unit appears to be malfunctioning, read through the OPERATION section of this ma nual first. If the problem persists, check the Troubleshooting Guide below and on the following page. The problem could be something very simple that can be solved without a service call.
21.
22 Limited Warranty Franklin Industries, L .L. C . , warrants this product to be free from defects in materials and workmanship for a period of one year from the date of the original purchase. Franklin also warrants the compressor for 5 years with a Parts - only warranty from the date of purchase.
23 Tested and certified to NSF standard 12 by NSF International FIM400 OM - E - 2 Printed in China.
Een belangrijk punt na aankoop van elk apparaat Franklin Industries, L.L.C. FIM400 4100 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Franklin Industries, L.L.C. FIM400 4100 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Franklin Industries, L.L.C. FIM400 4100 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Franklin Industries, L.L.C. FIM400 4100 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Franklin Industries, L.L.C. FIM400 4100 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Franklin Industries, L.L.C. FIM400 4100 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Franklin Industries, L.L.C. FIM400 4100 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Franklin Industries, L.L.C. FIM400 4100 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
