Gebruiksaanwijzing /service van het product DVD Duplication van de fabrikant EZQuest
Ga naar pagina of 55
EZQuest Duplicators King Boa DVD Duplication User's Manual.
Copyright and Trademark The information in this manual is subject to change without prior notice and does not represent a commitment on the part of vendor, who assumes no liability or re- sponsibility for any errors that may appear in this manual. This manual contains materials protected under International Copyright Laws.
Buttons and LCD There are four buttons and an LCD on the panel of the copy smart plus. They are described as follows. 1 2 4 3 5 1. It shows all functions and messages. 2. It is used to scroll up through functions or menus. 3. It is used to scroll down through functions or menus.
3. 4. Detect Drives 1. Copy There are 12 functions for you to use. Function 1 is Copy. You can press t to select other functions. l Place a source DVD into DVD-ROM. l Switch to function 1 Copy by pressing s . Place blank DVD disks into the DVD writers, and press ENT to start copying.
Chapter 5 Functions There are 12 functions: Copy, Test, Test & Copy, Verify, Compare, Prescan, Disc Info, Select Source, Image, Edit Track, Setup and Advanced Setup. Among the 12 functions, Edit Track is designed exclusively for editing a collection of favorite songs from CDs.
When copying is in progress, MB and time will decrease whereas the percentage of completion increase. When copying comes to an end, LCD will show the results as follows. The passed DVDs will eject automatically. 1.Copy OK: 03 5.2 Test Function 2 Test is to simulate the copying progress.
LCD will show the testing information as follows. Testing- DVD 0% 4213.4MB d:20:15 When the test comes to an end, LCD will show the results as follows. 2.Test OK: 03 Stopping the test halfway does not affect the DVD disks, but if the DVD-rewriteable disks contain important data, they may be destroyed.
When the test finishes, actual copying will begin as shown below. Copying- DVD 0% 4213.4MB d:20:15 When the whole process finishes, LCD will show the results as follows. 3.Test & Copy OK: 03 5.4 Verify Function 4 Verify is to examine if the target DVDs can be read correctly after copying.
When verification comes to an end, LCD will show the results as follows. 4.Verify OK: 03 5.5 Compare Function 5 Compare is to make a comparison between the source DVD and the target DVDs after copying. Select function 5. Put the source DVD onto DVD-ROM and the target DVDs onto DVD writers.
Press ENT to see the details of source 1 as shown below. Src: 01 DVD-ROM Total: 4213.4MB Press ENT to see the details of source 2. If the comparison is identical, LCD will show the message as follows. Src: 02 DVD-RW Identical If comparison fails, LCD will show the failure.
Press ENT to prescan. LCD will show the scanning information as follows. Scaning- DVD 0% 4213.4MB 40:40 When scanning finishes, and the source DVD can be read correctly, LCD will show the results as follows. PreScan OK! 5.7 Disc Info Function 7 Disc Info is to show the basic information of source DVD.
5.8 Select Source Function 8 Select Source is to let you select the data on DVD-ROM, DVD writers or HDD as the source from which copying will be done. 8.Select Source Select function 8. Press ENT , and then press s t to select the source as shown below.
5.9 Image Function 9 Image is valid only when you have installed a hard disk. This function includes 6 parts. They are Load, Delete Image, Image Info, Compare Image, Select Partition and Select Src Drive. The loaded data is called an image file. Select function 9.
After the image file is successfully loaded, LCD will show the results as follows. Image load OK If there is an image file existing in the current partition, the system will ask you whether to overwrite it or not. Please use s t to confirm Yes or No. Image Exists Overwrite?Yes 5.
After the image file is deleted, LCD will show the results as follows. Partition A: Image is deleted 5.9.3 Image Info This function is to show the basic information of an image file stored in a particular partition. First, select the function by pressing t .
Press ENT , and LCD will show the comparison information as follows. Compare- DVD 0% 4213.4MB 1:05:06 When comparison comes to an end, LCD will show the results as follows. Compare OK: 1 Fail: 0 Diff: 0 Press ENT to see the details of source 1 as shown below.
5.9.5 Select Partition This function is to select a partition in the hard disk. First, select the function by pressing t . 9-05.Image P: A Select Partition After installing a hard disk, your copy smart plus will format it automatically. Each partition will occupy 5GB.
First, select the function by pressing t . 9-06. Image P: A Image Src Drive Then, use s t to select DVD-ROM or any of the DVD writers as the source. Select Img Src: 01 IDE1 DVD-ROM After selecting the source such as DVD-ROM, you can press ENT , and LCD will show the message as follows.
Select function 10. 10. Edit Track 5.10.1 CD to CD On the above figure press ENT , and you will enter the following figure.Here the function CD to CD is to let you select a track or more from CD-ROM, and then copy into blank CD-R/RWs. 10-01. Edit Track CD to CD Edit On the above figure press ENT , and you will enter the following figure.
After selecting, please use s to move to the ìEndî menu as shown below. Select Track: End 1Trk03:25 Press ENT to finish the CD editing, and use s t to confirm Yes or No.
The system will ask if you want to keep editing. Please use s t to confirm Yes or No. as shown below. Continue edit next Disc?Yes If you want to keep editing, the current source CD will eject auctomatically, and the system will ask you to insert another new CD as shown below.
Press ENT to finish the CD editing, and use s t to confirm Yes or No. End edit disc and burn?Yes LCD will show the copying information as follows. Copying- 24X Edit 2/10 - > 2/2 On the above figure 2/2 means the second track of all tracks we have selected, and so far we have selected two tracks from two different CDs.
On the above figure Press ENT . The system will ask if you want to close all CDsí sessions. Please use s t to confirm Yes or No as shown below. Close all discís session? Yes After deciding to close, LCD will show the message as follows. Closing Session Please wait--- 5.
Suppose we decide to select the first track, then press ENT . A ì+î will appear beside 1/10 as shown below. But pressing ENT again may cancel the selection. Select Track: +1/10 03:25 After selecting, please use s to move to the ìEndî menu as shown below.
The system will ask if you want to keep editing. Please use s t to confirm Yes or No. as shown below. Continue edit next Disc?Yes If you want to keep editing, the current source CD will eject auctomatically, and the system will ask you to insert another new CD as shown below.
Then, the track as an image file will be loaded into HDD. LCD will show the loading information as follows. Load- P0 -24X Edit 2/10 - > 2/2 When loading comes to an end , LCD will show the message as follows. Image load OK The system will ask if you want to keep editing.
When burning finishes , LCD will show the results as follows. Burn Complete ! OK: 03 On the above figure press ESC to enter the following figure. Now press t to move the data from HDD template into a certain partition. Burn or Move to partition? Move After pressing t , you need to select a partition into which the data will be moved.
If the chosen partition has contained image data, the system will ask to overwrite or keep the data. Here please use s to overwrite. Image Exists Overwrite?Yes After pressing s , LCD will show the moving information as follows. Moving to P: A 0% When moving finishes, LCD will show the results as follows.
Use s t to select the track you want to play. Select Track: 1/10 03:25 After selecting and pressing ENT , LCD will show the playing information below. Playing Track-1 00:00 / 03:25 5.10.4 Close Session This function is to close CDs and let no data written into.
After pressing ENT , LCD will show the message as follows. Closing Session Please wait--- When closing finishes, LCD will show the results as follows. Closing Complete OK :3 Fail :0 5.11 Setup Function 11 Setup lets you change the default settings. Once you change a setting, remember to press ENT to save it.
5.11.1 Language On the above figure press ENT , and you will enter the following figure. The function Language lets you select a language in which messages can be shown on LCD. 11-01. Setup Language Press ENT to enter the following figure. Here LCD only supports English.
5.11.3 Read Speed On the above figure press ESC and t to enter the following figure. The function Read Speed lets you control the reading speed of target DVDs. 11-03. Setup Read Speed Press ENT to enter the following figure. The default is maximum, but there are still other choices: 32X, 16X and 8X.
5.11.5 Startup Menu On the above figure press ESC and t to enter the following figure. Startup Menu lets you select any one of the functions except Adv Setup as the first item appearing on the menu whenever you turn on the copy smart plus. 11-05. Setup Startup Menu Press ENT to enter the following figure.
5.11.7 Auto Compare On the above figure press ESC and t to enter the following figure. Auto Compare is to compare automatically the source DVD and the target DVDs after copying. 11-07. Setup Auto Compare Press ENT to enter the following figure. The default is Off.
5.11.9 Eject Disc On the above figure press ESC and t to enter the following figure. Eject Disc provides three choices. They are Eject Good Only, Eject All Disc, and Do Not Eject. Eject Good Only means that the DVDs will eject automatically only when they are copied successfully.
Press ENT to enter the following figure. The default is On. Press t to select Off. Burn On The Fly On If your copy smart plus doesnít connect with a hard disk, LCD will show the message as follows.
5.11.12 Button Sound On the above figure press ESC and t to enter the following figure. Button Sound lets you control the sound of a button when you press it. 11-12. Setup Button Sound Press ENT to enter the next figure. The default is On. Press t to select Off.
Press ENT to enter the next figure. DVD-ROM DVD-116 1.22 Press t twice to enter the next figure. 02 IDE2 Master DVD-RW : PIONEER Press ENT to enter the next figure. DVD-RW DVR-103 1.80 5.11.14 System Info On the above figure press ESC and t to enter the following figure.
5.12 Adv Setup On the above figure press ESC to return to Function 11. Then, press ESC for 2 seconds to enter Function 12 as the following figure shows.
5.12.2 Overburn On the above figure press ESC and t to enter the following figure. Overburn lets you decide whether to copy beyond the limit of the CD or not. 12-02. Adv Setup Overburn Press ENT to enter the following figure. The default is Off. Press t to select On.
5.12.4 Format HDD On the above figure press ESC and t to enter the following figure. Format HDD is to partition the hard disk. But before formatting, all data on the hard disk will be deleted. 12-04. Adv Setup Format HDD Press ENT to enter the next figure.
Press ENT to enter the next figure. Use s t to confirm Disk or Parti. Verify Disk or Partition? Disk Press ENT to verify. After verification LCD will show the results as follows. Verify Hard Disk OK! 5.12.6 Burn-in On the above figure press ESC and t to enter the following figure.
Press ENT and use s t to select the time of simulation such as 1, 2, 3...1000 or Run Continuous. The figure below shows Run Continuous. Sel burn-in num: Run Continuous Press ESC , ENT , t to select Erase & Copy as the following figure shows. Erase & Copy is to erase and write repeatedly.
You can get the newest firmware version from ACARD by e-mail, or download it directly from the web site: http://www.acard.com Then, unzip the file ìcdxxx.
Press ENT to enter the next figure. Follow the instructions on LCD to do the button test. After that, the system will do the self-test of SDRAM, the hardware connection test and flash test. All test results will be shown on LCD. It is the easiest way to know if the system can work well.
When default loading finishes, LCD will show the results as follows. Load Default OK 5.12.11 CD+G On the above figure press ESC and t to enter the following figure. CD+G is a kind of special copying format. This function supports the special format. 12-11.
Troubleshooting 6.1 About LCD After powering on if there is no LCD, please check if the connection of power cord is frim and the environment of power outlet is normal. 6.2 About Error Messages During Copy, Test, Compare and Verify, etc. if you press ESC to abort, an error message will appear on LCD.
6.4 About Buttons If you press any one of the four buttons on the panel, but there is no response, it is perhaps that the button cannot function well. Please inspect the jumper setting. 6.5 About DVD Writer Not Readable After copying if the DVD writer is not readable, please use Compare to examine, or get another DVD-ROM to test.
6.8 About Function 12 and Cancellation If you want to execute function 12 Advanced Setup, you can press ESC for 2 seconds. And during operation if you want to cancel a function like Copy, Test, Verify and so on, you can press ESC for 2 seconds, too.
Appendix 1 List of Functions 1 Copy 2 Test 3 Test & Copy 4 Verify 5 Compare 6 Prescan 7 Disc Info 8 Select Source 9 Image (It works only when a hard disk is connected) 9.1 Load 9.2 Delete Image 9.3 Image Info 9.4 Compare Image 9.5 Select Partition (Each partition is 5GB) 9.
11.10 Burn On The Fly (Default is On) 11.11 Burn Mode (Default is DAO) 11.12 Button Sound (Default is On) 11.13 Device Info 11.14 System Info 11.15 Quick Erase 11.16 Quick Erase 12 Adv Setup 12.1 UnderRun Protect (Default is On) 12.2 Overburn (Default is Off) 12.
Appendix 2 LCD Messages 1. Normal Conditions: Initialize SDRAM ............................................Initialize the memory of the system. Detect Drives ..............................Detect what drives are connected with the system. User Abort! .
Press a Key to Eject Good Disc ... Press any ket to eject the good disc after copying Press a Key to Eject Fail Disc ......Press any key to eject the failed disc after copying. DVD-RW does not Support the Func .......... DVD-RW doesnít support this function.
Verify Hard Disk OK! ................................... The hard disk is verified successfully. Verify Hard Disk Fail! ............................ The hard disk is not verified successfully. Verify Partition Header! .................................
Check Sum Error!. ................................................. The udpated firmware has errors. Source canít be Hard Disk! .......During comparison the source cannot be hard disk. Last update F/W OK! ................................... The firmware is updated successfully.
Een belangrijk punt na aankoop van elk apparaat EZQuest DVD Duplication (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen EZQuest DVD Duplication heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens EZQuest DVD Duplication vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding EZQuest DVD Duplication leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over EZQuest DVD Duplication krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van EZQuest DVD Duplication bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de EZQuest DVD Duplication kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met EZQuest DVD Duplication . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
