Gebruiksaanwijzing /service van het product D01T van de fabrikant Dell
Ga naar pagina of 73
Dell Precision Workstation T5610 Owner's Manual Regulatory Model: D01T Regulatory Type: D01T003.
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Contents 1 Working on Your Computer....................................................................................................... 5 Before Working Inside Your Computer ..........................................................................
Removing the Speaker ............................................................................................................................................ 35 Installing the Speaker ...............................................................
1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety.
6. Remove the cover. CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal components.
5. If required, verify that the computer works correctly by running the Dell Diagnostics. 7.
8.
2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Recommended Tools The procedures in this document may req.
System Overview Figure 1. Inside View of the T5610 Computer 1. air tunnel 2. front bezel 3. optical drive 4. air baffle 5. hard drives 6. air duct 7. power supply unit (PSU) 8. coin-cell battery 9. PCI card 10. memory module 11. intrusion switch 12. heatsink with integrated fan Removing the Power Supply Unit (PSU) 1.
3. Hold the handle bar and press down on the blue latch to release the PSU. 4. Hold the handle bar to slide the PSU out of the computer. Installing the Power Supply Unit (PSU) 1. Hold the PSU handle and slide the PSU into the computer. 2. Follow the procedures in After Working Inside Your Computer .
Removing the Cover 1. Follow the procedures in Before Working Inside Your Computer . 2. Lay down the computer on its side with the latch facing up. 3. Lift up the cover-release latch.
4. Lift the cover upward to a 45–degree angle, and remove it from the computer. Installing the Cover 1. Place the computer cover on the chassis. 2. Press down on the computer cover until it clicks into place. 3. Follow the procedures in After Working Inside Your Computer .
4. Rotate and pull the bezel panel away from the computer to release the hooks on the opposite edge of the bezel from the chassis. Installing the Front Bezel 1. Insert the hooks along the bottom edge of the front panel into the slots on the chassis front.
4. Unthread the cables from the latches. 5. Press on the clasp to release the latch holding the cables on the side of the optical-drive cage. 15.
6. Press down on the latch and lift up the cables. 7. Lift up the release latch on top of the optical-drive cage. 8. Holding the release latch, slide the optical-drive cage from the optical-drive compartment.
Installing the Optical Drive 1. Lift the release latch, and slide the optical-drive cage inside the compartment. 2. Press on the clasp to release the latch and thread the cables into the holder. 3. Connect the power cable to the back of the optical drive.
5. Slide the hard drive out of the compartment. 6. If a 2.5–inch hard drive is installed, remove the screws and lift up the drive to remove it from the hard-drive caddy.
3. Identify the thermal sensor connected to the system board. 4. Disconnect the thermal sensor from the system board. 5. Release the latch that secures the thermal sensor.
Removing the Input/Output (I/O) Panel 1. Follow the procedures in Before Working On Your Computer . 2. Remove: a. cover b. front bezel 3. Remove the screws that secure the USB 3.0 module to the I/O panel. 4. Remove the USB 3.0 module from the chassis.
5. Disconnect the cables to release the I/O panel. 6. Remove the screws which secure the I/O panel to the chassis. 7. Remove the I/O panel from the chassis. Installing the Input/Output (I/O) Panel 1. Replace the I/O panel in its slot. 2. Tighten the screws securing the I/O panel to the chassis 3.
Removing the Air Tunnel NOTE: The air tunnel is an optional component and your computer may not ship with it. 1. Follow the procedures in Before Working On Your Computer . 2. Remove: a. cover b. optical drive 3. Press down on the retention tab on the air tunnel and lift it from the computer.
3. Press down on the memory-securing clips on each side of the memory module, and lift the memory module upwards to remove it from the computer. Installing the Memory 1. Insert the memory module into the memory socket. 2. Press down on the memory module until the securing clips secure the memory in place.
Removing the Heatsink 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the cover. 3. Disconnect the heatsink cable from the system board.
5. Grip the heatsink and lift it away from the computer. Installing the Heatsink 1. Place the heatsink inside the computer. 2. Tighten the captive screws to secure the heatsink to the system board. 3. Connect the heatsink cable to the system board. 4.
3. Slide out the grommets that secure the heatsink fan to the heatsink assembly. 4. Slide the heatsink fan from the heatsink assembly. Installing the Heatsink Fan 1. Slide the heatsink fan into heatsink assembly. 2. Plug in the grommets to secure the heatsink fan to the heatsink assembly.
Removing the Processor 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a. cover b. air tunnel (if available) c. heatsink 3. To remove the processor: NOTE: The processor cover is secured by two levers. They have icons that indicate which lever needs to be opened first and which lever closes first.
Installing the Processor 1. Place the processor in its socket. 2. Replace the processor cover. NOTE: The processor cover is secured by two levers. They have icons that indicate which lever needs to be opened first and which lever closes first. 3. Slide the first lever sideways into the retention hook to secure the processor.
4. Remove the screw that secures the metal plate to the system fan. 5. Press the latches on either side of the metal plate to release it. 29.
6. Lift the metal plate out of the chassis. 7. Remove the screws that secure the drive bay. 8. Slide the latch out to release the air baffle. 30.
9. Remove the air baffle out of the computer. 10. Remove the PSU cable from the clips. 11. Disconnect the system-fan cables from the system board. 31.
12. Remove the screws that secure the system-fan assembly to the chassis. 13. Lift the system-fan assembly from the chassis. 14. Pry away the grommets to remove the system fans from the system-fan assembly. CAUTION: Using excessive force may damage the grommets.
15. Remove the system fans from the system-fan assembly. Installing the System Fan 1. Place the system fans in the system-fan assembly and attach the grommets. 2. Place the system-fan assembly in the chassis. 3. Install the screws to secure the system-fan assembly to the chassis.
3. Slide the baffle cover from its slot towards the front. 4. Remove the baffle cover from the computer. 5. Disconnect the power cables from the system board.
6. Remove the screws securing the PSU card to the slot. 7. Remove the PSU card from the computer. Installing the PSU Card 1. Replace the PSU card in its slot. 2. Tighten the screws to secure the PSU card in its slot. 3. Connect the power cables to the connectors on the system board.
3. Disconnect the speaker cable from the system board. 4. Press down the clasp, lift and remove the speaker. Installing the Speaker 1. Replace the speaker and fix the clasp. 2. Connect the speaker cable to the system board. 3. Install the cover. 4. Follow the procedures in After Working Inside Your Computer .
Removing the System Board 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove: a. cover b. coin-cell battery c. PCI card d. memory module(s) e. thermal sensor f. air tunnel (if available) g. heatsink fan h. heatsink i. processor 3.
4. Disconnect the cables connected to the system board. 5. Remove the screws that secure the system board. 38.
6. Slide the system board towards the system-fan assembly. 7. Lift the system board away from the chassis. Installing the System Board 1. Align the system board to the port connectors on the back of the chassis and place the system board in the chassis.
4. Install: a. processor b. memory module(s) c. coin-cell battery d. heatsink fan e. heatsink f. speaker g. I/O panel h. PCI card i. PSU card j. system fan k. hard drive l. optical drive m. thermal sensor n. cover o. power supply unit (PSU) 5. Follow the procedures in After Working Inside Your Computer .
1. PCI slot (slot 6) 2. PCIe x16 slot (wired as x4) 3. PCIe x16 slot 4. PCIe x1 slot 5. PCIe x16 slot 6. PCIe x16 slot (wired as x8) 7. USB 3.0 front-panel connector 8. intrusion-switch connector 9. DIMM slots (available only when optional second processor is installed) 10.
42.
3 Additional Information This section provides information for the additional features that are part of your computer. Memory Module Guidelines To ensure optimal performance of your computer, observe the following general guidelines when configuring your system memory: • Memory modules of different sizes can be mixed (for example, 2 GB and 4 GB).
44.
4 System Setup System Setup enables you to manage your computer hardware and specify BIOS ‐ level options. From the System Setup, you can: • Change the NVRAM settings after you add or remove hardw.
Keys Navigation <Enter> Allows you to select a value in the selected field (if applicable) or follow the link in the field. Spacebar Expands or collapses a drop ‐ down list, if applicable. <Tab> Moves to the next focus area. NOTE: For the standard graphics browser only.
Option Description Date/Time Allows you to set the date and time. The changes to the system date and time takes effect immediately. Table 3. System Configuration Option Description Integrated NIC Allows you to configure the integrated network controller.
Option Description • SATA2–HDD2 • SATA2–ODD0 • SATA3–HDD1 • SATA2–HDD3 • SATA2–ODD1 Default Setting: All drives are enabled. NOTE: If the hard drives are connected to a RAID controller card, the hard drives will display {none} in all the fields.
Option Description • Enabled (Default) • Disabled Table 4. Video Option Description Primary Video Slot Allows you to configure primary boot video device. The options are: • Auto (Default) • SLOT 1 • SLOT 2: VGA Compatible • SLOT 3 • SLOT 4 • SLOT 5 • SLOT 6 Table 5.
Option Description CPU XD Support Allows you to enable the Execute Disable mode of the processor. Default Setting: Enable CPU XD Support OROM Keyboard Access Allows you to determine whether users are able to enter Option ROM Configuration screens via hotkeys during boot.
Option Description NOTE: • The options displayed could be different depending on the installed processor(s). • The options depend on the number of cores supported by the installed processor (All, 1, 2, N-1 for N-Core Processors) Intel SpeedStep Allows you to enable or disable the Intel SpeedStep feature.
Option Description Deep Sleep Control Allows you to define the controls when Deep Sleep is enabled. • Disabled (Default) • Enabled in S5 only • Enabled in S4 and S5 Fan Speed Control Allows you to control the speed of the system fan.
Option Description • Enable Intel Virtualization Technology - This option is enabled by default. VT for Direct I/O Enables or disables the Virtual Machine Monitor (VMM) from utilizing the additional hardware capabilities provided by Intel Virtualization technology for direct I/O.
11. Select your preferred download method in the Please select your download method below window ; click Download File . The File Download window appears. 12. Click Save to save the file on your computer. 13. Click Run to install the updated BIOS settings on your computer.
8. Press <Y> to save the changes. The computer reboots. Deleting or Changing an Existing System and/or Setup Password Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change the existing System and/or Setup password.
56.
5 Diagnostics If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical assistance. The purpose of running diagnostics is to test your computer's hardware without requiring additional equipment or risking data loss.
58.
6 Troubleshooting Your Computer You can troubleshoot your computer using indicators like Diagnostic Lights, Beep Codes, and Error Messages during the operation of the computer. Diagnostic LEDs NOTE: The diagnostic LEDs only serve as an indicator of the progress through the Power-On Self Test (POST) process.
• If available, install verified working memory of the same type into your computer. A possible graphics card failure has occurred. • Ensure that the display/monitor is plugged into a discrete graphic card. • Re-seat any installed graphics cards.
A possible system board failure has occurred. • Disconnect all internal and external peripherals, and re-start the computer. If the computer boots, add the peripheral cards back one by one until you find the bad one. • If the problem persists, the system board is faulty.
Error Message Alert! Processor type mismatch. Install like processor or one processor. Alert! Processor speed mismatch Install like processor or one processor.
Error Message Dell Reliable Memory Technology (RMT) has discovered and isolated errors in system memory. You may continue to work. Memory module replacement is recommended. Please refer to the RMT Event log screen in BIOS setup for specific DIMM information.
64.
7 Technical Specifications NOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. For comprehensive specification of your computer go to Specifications’ section in your Owner’s Manual available on the support site at dell.
Feature Specification T3610 / T5610 / T7610 4 GB Maximum memory T3610 / T5610 128 GB T7610 512 GB Table 20. Video Feature Specification Discrete (PCIe 3.0/2.0 x16) T3610 / T5610 up to 2 full-height, full-length (maximum of 300 W) T7610 up to 4 full-height, full length (maximum of 600 W) Table 21.
Feature Specification USB: Front ports USB 3.0, 5 Gbps (1 port); USB 2.0, 480 Mbps (3 ports) Rear ports USB 3.0, 5 Gbps (3 ports); USB 2.0, 480 Mbps (3 ports) Internal ports USB 2.0, 480 Mbps (3 ports) Table 24. Drives Feature Specification T3610 /T5610 Externally accessible: Slimline SATA optical bays one 5.
Feature Specification T7610 two RJ-45 Serial one 9-pin connector USB T3610 / T5610 / T7610 • front panel — three USB 2.0, and one USB 3.0 • back panel — three USB 2.0, and one USB 3.0 • internal — three USB 2.0 Video Video card dependent • DVI connector • DisplayPort • DMS-59 Table 26.
Feature Specification PCI 2.3 one 124-pin connector Front I/O: Front USB one 14–pin connector Internal USB one type A female, one dual-port 2x5 header Front panel control one 2x14 pin connector Fron.
Feature Specification amber/blinking light — see the service manual for specific diagnostic codes. Table 28. Power Feature Specification Coin-cell battery 3 V CR2032 lithium coin cell Voltage 100 VA.
Feature Specification Height (with feet) 433.40 mm (17.06 inches) Height (without feet) 430.50 mm (16.95 inches) Width 216.00 mm (8.51 inches) Depth 525.
72.
8 Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options.
Een belangrijk punt na aankoop van elk apparaat Dell D01T (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Dell D01T heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Dell D01T vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Dell D01T leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Dell D01T krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Dell D01T bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Dell D01T kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Dell D01T . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
