Gebruiksaanwijzing /service van het product CAN/CSA B365 van de fabrikant Dansons Group
Ga naar pagina of 12
PELLET STOVE OPERATIONS GUIDE CAN/CSA B365 Installation Code For Solid-Fuel-Burning Appliances and Equipment in Canada and NFPA 211 Chimney, Fireplaces, Vents and Solid Fuel Burning Appliances in the USA Manufactured by READ THIS ENTIRE MANUAL BEFORE INSTALLING YOUR PELLET STOVE/HEATER/INSERT.
Dear Pellet Appliance Owner, UPDATES Updated manuals, product registration and warranty information can be found on our website: Thank you for selecting our wood pellet stove! 2 Sincerely, Dansons Group Inc. and Canadian Comfort Industries www.dansons.
LIGHTING PROCEDURE STARTUP CHECKLIST 2 A B C D 1 3 The COMBUSTION FAN (exhaust) will start and operate at full speed for 60 seconds, then will slow to match the startup rate On a primed auger system , pellets will begin to fall into the BURN GRATE, and the igniter will automatically ignite pellets in approximately 3 to 7 minutes.
INITIAL SETUP 1 2 Slide open or close the damper as needed to obtain a fire that is brisk enough to carry ash out of the grate, but not so brisk that it carries whole pellets out as well; this is known as popcorning . Normally, you should find that the damper will need to be 1/4” to 1/2” open.
3 A B FINE TUNING YOUR STOVE FUEL FEED RATE SETTING #1 (LOW) FUEL FEED RATE SETTING #4 (HIGH) INCREASES feed rate DECREASES feed rate Do NOT use a metal object to adjust your trim pods. Try using a plastic non-metallc object (eg. insulated shaft screwdriver, pen cap, etc.
The performance of your pellet appliance is greatly affected by the type and quality of wood pellets burned. As the heat output of various brands of pellets differs, so will the performance and heat output of your appliance. We recommend the use of screened pellet fuel in order to reduce the amount of fines your stove will have to cope with.
NOTE: It is much easier to remove fines from pellets before they are placed in the stove than it is to service your stove for a plugged hopper, jammed auger or plugged exhaust system. Pellets with excessive sawdust may be screened to remove most of the fines.
ASH TRAPS - Remove the rear burn plate from the firebox area. This will expose the 2 ash traps and the pellet fuel drop chute. Fly ash may be removed by vacuuming inside the trap area with an approved ash vacuum ( A HOME SHOP VAC MAY BE USED TO REMOVE ASH FROM YOUR STOVE *ONLY* WHEN THE ASHES HAVE COOLED ).
INSPECT AND CLEAN VENTING - Fly ash will collect in the exhaust venting system and restrict the flow of flue gases. Check the clean out tees and elbows in the system periodically to determine the required schedule of cleaning. To remove dust from the vent pipe, lightly tap on the pipe to dislodge loose ash.
GUIDE TO TROUBLESHOOTING Proper cleaning, maintenance and use of quality pellets will prevent common operational issues with your pellet stove. However, when your appliance is simply operating poorly or not at all, the following troubleshooting tips may be helpful.
LIMITED WARRANTY CANADIAN COMFORT INDUSTRIES (CCI) LIMITED WARRANTY CCI wood pellet and corn appliances carry a one (1) year - parts only - on electrical components and a five (5) year limited warrant.
COPYRIGHT Copyright 2006, Canadian Comfort Industries. All rights reserved. No part of this manual may be copied, transmitted, transcribed, stored in a retrieval system in any form or by any means wit.
Een belangrijk punt na aankoop van elk apparaat Dansons Group CAN/CSA B365 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Dansons Group CAN/CSA B365 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Dansons Group CAN/CSA B365 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Dansons Group CAN/CSA B365 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Dansons Group CAN/CSA B365 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Dansons Group CAN/CSA B365 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Dansons Group CAN/CSA B365 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Dansons Group CAN/CSA B365 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.