




Übersetzung der Originalbetriebsanleitung 13
Vertaling van de oorspronkelijke gebruiksaanwijzing 23
Traduction de la notice originale 32
Traducción del manual original 41
Traduzione delle istruzioni originali 50
Översättning av bruksanvisning i original 60
Alkuperäisten ohjeiden käännös 68
Eredeti használati utasítás fordítása 76
Překlad originálního návodu k obsluze 85
WWW.FERM.COM
Original instructions 04






13 15 16 · 11 10 23



Mitre 45º, Bevel 45º 40x210mm Mitre 45º, Bevel 0º 70x210mm Mitre 0º, Bevel 45º 40x310mm Weight 15 kg Lpa (sound pressure) 97+3 dB(A) Lwa (acoustic capacity) 110+3 dB(A) Vibration level
Thank you for buying this Ferm product. By doing so you now have an excellent product, delivered by one of Europe’s leading suppliers. All products delivered to you by Ferm are manufactured according to the highest standards of performance and safety. As part of our philosophy we also provide an excellent customer service, backed by our comprehensive warranty. We hope you will enjoy using this product for many years to come.
Vibration level The vibration emission level stated in this instruction manual has been measured in accordance with a standardised test given in EN 61029-1; it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned
The numbers in the following text refer to the pictures on page 2-3
Read the operating instructions carefully before using this device. Familiarise yourself with its functions and basic operation. Service the device as per the instructions to ensure that it always functions properly. The operating instructions and the accompanying documentation must be kept in the vicinity of the device.
- using the tool for different applications, or with different or poorly maintainted accessories, may significantly increase the exposure level - the times when the tool is switched off or when it is running but not actually doing the job, may significantly reduce the exposure level
Protect yourself against the effects of vibration by maintaining the tool and its accessories, keeping your hands warm, and organizing your work patterns
Intended use The electro tool is intended as a stationary machine for making straight lengthways and crossways cuts in wood. Horizontal mitre angles of -45° to +45° as well as vertical bevel angles of -45° are possible.
Package contents 1 Dust adapter 1 Pair of safety glasses 1 Carbon brush set 1 Pair of earplugs 2 Side bars 1 Anti-tip over support
Contents 1. Machine information 2. Safety 3. Mounting accessories 4. Operation 5. Service & Maintenance
Check the machine, loose parts and accessories for transport damage.
Features Figs. 1, 2, 3, 4 and 5 1. On/off switch 2. On/off switch for laser 3. Unlock button (Blade protective cover) 4. Cover carbon brush 5. Lock-pin 6. Blade protective cover 7. Workpiece clamp 8. Guide fence 9. Knob adjusting saw angle 10. Locking knob 11. Locking paddle 12. Knob over sliding support 13. Connection dust bag
Mains voltage 230 V, 50Hz Capacity 2000 W S6 (25%) / 1800 W S1 Machine class II (double insulated) No load speed 5000/min Saw blade measurement 255x30x2.8mm Angle for mitring 45º (left and right) Angle for bevelling 45º (only left) Mitre saw maximum sawing capacity: Mitre 0º, Bevel 0º 70x310mm
Technical specifications

When using the machine, always carefully follow the safety precautions supplied and the safety instructions given below.
Denotes risk of personal injury, loss of life or damage to the tool in case of non- observance of the instructions in this manual.
Indicates the presence of an electrical voltage.
Keep bystanders away.
Wear eye and ear protection.
Wear a dust mask protection
Before each use of the saw Check the machine. If any part of the machine is missing, bent or in any other way unusable, or when an electrical defect occurs, turn the machine off and take the plug out of the socket. Replace all missing, damaged or defective parts before using the machine again.
To fix the saw blade in the slot and to prevent the piece of work from moving, follow the instructions below.
Explanation of symbols

Additional safety instructions 1. When using the saw blades with hard metal teeth (Carbon tipped) it is advisable to use blades with a negative or slightly positive cutting angle. Do not use any saw blades with deeply cut teeth. They can grip the protective cap. 2. Attention: First carefully assemble all the parts before starting work. Follow the procedure as indicated. 3. If you are not familiar with using such a machine, you would be better to be informed first by a professional, an instructor or by a technician. 4. Always clamp or press the workpiece firmly against the saw guide, before you carry out the process. The use of all possible clamping set-ups is preferable to using your hands. 5. Important: If you are holding the workpiece by hand for the process to be carried out, keep a minimum distance of 100 mm from the saw blade. 6. Always press the workpiece against the bench. 7. Keep the saw blade sharp and check regularly whether it rotates freely without abnormal vibrations. Replace the saw blade if necessary. 8. Allow the machine to rotate freely until it reaches the maximum number of revolutions, before you start the process. 9. Maintain the air inlets at the back and the bottom of the bench saw machine and electric engine for a longer machine life. Dust piles must be removed.

10. Always lock the different degree set-ups before you start processing. 11. Only buy suitable saw blades with a number of revolutions of at least 5.000 revolutions per minute. 12. Only use the correct saw blade. Too small or too big saw blades are extremely dangerous. 13. Regularly inspect the saw blade for any faults. Replace the saw blade if necessary. 14. Grease the new saw blade and clean the flanges before you assemble the new blade. Then assemble the blade in the correct direction and pull the flanges firmly using the central bolt. 15. Only use original flanges. All other types are not suitable. 16. Never work without the protective cap of the saw blade. 17. The moving part of the protective cap must also remain assembled. 18. Never grease the saw blade while it is rotating. 19. Always keep your hands removed from the track of the saw blades. 20. Never pick up the workpiece by grasping with your hands along or behind the saw blade. 21. Ensure that the workpiece never touches the saw blade before the machine has been switched on. 22. Never process metal or stone sorts with this machine. 23. Use support aids in order to support long workpieces. 24. Never use the machine in a dangerous environment, where inflammable gases or fluids are present. 25. Never leave the machine unattended without first disconnecting it from the mains voltage. 26. If you hear abnormal noises, try to trace them or take the machine to a recognized fitter, or repair company. 27. If a part is broken or damaged, replace it or repair it immediately. 28. Never stand in the track of the saw blade but stand to the left or the right of the saw bench. 29. Your hands must likewise be placed next to the track of the saw blade. 30. Always use the feedstick to push the wood through the saw. 31. Always place the wood at the front of the saw bench and then push it further back. 32. For mitring only the adjustable guide must be used and the fence must be removed.

Only lift the machine by the solid underside of the machine.
While the machine is in use With frequent use of the machine, do not let routine lead to mistakes. Remember that a slight lack of concentration can lead to serious injuries in a fraction of a second.
Loud noise can lead to hearing damage. Ensure that you wear ear protectors. Ensure that the cavity blade is not bent, this can also cause noise.
Before all work on the machine, pull the mains plug.
Check that all locks and tensioning devices are secure: • Turn the locking knob (12) on the turntable counterclockwise
Transport

stop before you take your hands off the machine.
also the enclosed safety instructions.
Always check that the power supply corresponds to the voltage on the rating plate.
Class ll machine. Your machine is double insulated; therefore no earthwire is required.
Replacing cables or plugs Immediately throw away old cables or plugs when they have been replaced by new ones. It is dangerous to insert the plug of a loose cable in the wall outlet.
To prevent damaging the motor must be regularly freed of chips and dust to ensure correct cooling.
Installation of the machine on a workbench or on the subframe. Fig. 5. This machine is a stationary machine and for safety reasons must always be firmly installed and not used for mobile applications.
You can install the machine in two ways: a. As a stationary machine on a workbench. In
this case the machine must be secured to the workbench with 4 bolts. b. As a stationary machine on the subframe.
Electrical safety When using electric machines always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury. Read the following safety instructions and
In this case the machine must be secured to the subframe with 4 bolts and the subframe anchored to the floor or to a floor plate with dimensions of at least 1 square meter.

Adjusting the cutting angle Fig. 2. Adjusting Mitre Angles The mitre angle can be set between 45° left side and 45° right side
Changing the saw blades Fig. 4 and 5
Only use saw blades that are sharp and undamaged. You must immediately replace chipped or bent saw blades.
- Loosen the locking knob (10) - Press the locking paddle (11) and turn the saw table left or right by the locking knob (10) until the angle indicator (23) indicates the required angle. - Release the locking paddle (11) and tighten the locking knob (10)
Do not use a blade too thick to allow the outer blade washer to engage with the flats on the spindle. This will prevent the blade screw from securing the blade on the spindle.
Pre-settings (quick settings) on the following degrees: -45°, -30°, -22.5°, -15°, 0°, 15°, 22.5°, 30°, 45°.
- Press the locking paddle (11) when turning the baseplate, release the paddle before reaching the requested degrees and the plate with “click” into the pre-setting itself.
Adjusting Bevel Angles Fig. 1 and 3 The bevel angle can be set between 0° and 45°.
- Loosen the adjusting knob (9) - Tilt the saw by using the handle until the angle indicator (14) indicates the required angle. - Tighten the adjusting knob (9)
Changing the carbon brushes Fig. 2 - Disconnect the machine from the power supply - Unscrew the two covers (4) on the front and backside of the motor housing. - Replace the carbon brushes with the exact type of brushes

- Tighten the covers (4) again. Note: Always replace both carbon brushes at the same time, never use a mixture of old and new brushes.
Mounting the dust bag Fig. 1 Press in the clamp of the dust bag (13) and slide it onto the opening on the back of the machine. The dust bag stays in place when you release the clamp.
Using the mitre saw Fig. 1
Before use, always check for faults or defects!
Always make sure that the machine is not connected to the mains electricity when you carry out any maintenance of the mechanism.
Slide rails Dirt can damage the slide rails and thereupon the operating of the machine.
These machines are designed to function for a long time without any problems with a minimum of maintenance. By cleaning the machine regularly and using it in the correct way you can contribute to a long life of your machine.
Cleaning Clean the machine housing regularly with a soft cloth, preferably after each time you use the machine. Make sure that the ventilation slots are free of dust and dirt. For stubborn dirt use a soft cloth dampened with soapy water. Never use solvents such as benzene, alcohol, ammonia, etc. These types of solvents can damage the plastic parts.
Using the slide-function Fig. 1
The machine must be firmly bolted to a workbench.
Problem solving 1. The motor does not start • The plug is not in the socket
Use the slide-function for sawing wide workpieces:

Environment To prevent damage during transport the machine is delivered in sturdy packaging. The packaging is made of recyclable material wherever possible, so make use of the possibility of recycling the packaging. When you replace a machine, take the old one to your local dealer. Here it will be dealt with in an environmentally friendly way.
Damaged and/or disposed of electrical or electronic devices must be dropped off at recycling stations intended for that purpose.
Warranty Read the warranty conditions on the separately supplied warranty card.
The product and the user manual are subject to change. Specifications can be changed without further notice.
Lubrication The machine does not need any extra lubrication.
Faults Should a fault occur, e.g. after wear of a part, please contact the service address on the warranty card. In the back of this manual you find an exploded view showing the parts that can be ordered.
Eigenaren en ons team reageren doorgaans binnen een dag — en uw vraag helpt ook de volgende persoon.
Stel als eerste een vraag — andere eigenaren of ons team geven antwoord.