NL
AL-KO logo
Officiële handleiding

Al-ko BC 225 L

264 pagina's·9.2 MB·Grastrimmer·PDF·ENJA
Al-ko BC 225 L
Inhoudsopgave 34 secties Introduction · Intended use · Safety instructions · Explanation of symbols · … TonenVerbergen
Page 1 of the Al-ko BC 225 L user manual — Explanation of symbols
Pagina 1 · klik om te vergroten
Pagina 1

Introduction

Intended use

Read this documentation before starting up the machine. This is a precondition for safe working and flawless operation.

This device is intended for trimming and mowing lawns on private premises.

Using this device for any other or additional purpose is con sidered contrary to its intended use.

„ „ Observe the safety warnings in this documentation and

on the machine. „ „ This documentation is a permanent integral part of the

product described and must be passed on to the new owner if the machine is sold.

Safety instructions

Explanation of symbols

„ „ The machine may only be used in perfect technical con

dition. „ „ Only work when there is adequate daylight or artificial

lighting „ „ The machine must not be operated with different cutting

tools or attachments. „ „ Wear appropriate working clothes:

Special instructions for greater ease of understand ing and improved handling.

„ „ Long trousers, sturdy footwear, gloves

„ „ Safety helmet, safety goggles, ear defenders

Meaning of symbols on the machine

„ „ Always ensure stability when working.

„ „ The machine must not be operated if the operator is un

der the influence of alcohol, drugs or medication. „ „ Always operate the machine with both hands.

„ „ Keep the handles dry and clean.

Read the instruction manual

„ „ Keep body and clothing away from cutting parts.

„ „ Keep third parties away from the danger area.

Wear safety goggles, safety helmet, ear defenders

„ „ Remove foreign bodies from the working area.

„ „ Always keep the guard, string head and engine free of

mowing debris „ „ When leaving the machine:

„ „ Switch off the engine.

„ „ Wait until the cutting parts have come to a standstill.

„ „ Do not leave the machine unattended.

Only operate the equipment with cutting strings.

„ „ Never allow children or untrained persons to operate

or service the machine. There may be local regulations regarding minimum age requirements for operating the machine. „ „ Accident prevention regulations must be observed.

„ „ The user is responsible for accidents involving other

The distance between the device and other persons must be at least 15 m.

persons and their property.

BC 225 L: Blades not permitted!

Show 4 more labels / short text on this page
 ·  · Wear gloves · Wear safety shoes
Page 2 of the Al-ko BC 225 L user manual — Specification
Pagina 2 · klik om te vergroten
Pagina 2
Al-ko BC 225 L — Safety and protective equipment diagram (page 2)
Afb. 1 · Safety and protective equipment

Safety and protective equipment

Emergency Stop

Stone impact guard

In the event of an emergency, swith the ignition switch to “STOP”.

Protects the operator from ejected objects. The integrated cutter shortens the cutting string to the permissible length.

Specification

Al-ko BC 225 L — Specification diagram (page 2)
Afb. 2 · Specification

Dry weight (EN ISO 11806) 7,1 kg 5,5 kg

Sound power level ISO 22868 113 dB(A) K = 3,0 dB (A) 109 dB(A) K = 3,0 dB (A)

Sound pressure level ISO 22868 98,5 dB(A) 105,5 dB(A)

Vibration ISO 22867 6,2 m/s² K=1,5 m/s² 3 m/s² K=1,5 m/s²



Page 3 of the Al-ko BC 225 L user manual — BC 225 L assembly
Pagina 3 · klik om te vergroten
Pagina 3

BC 225 L assembly

BC 225 B assembly

Parts overview (Fig. 1)

Parts overview (Fig. 1)

5 Lever, see Starting the engine

5 Lever, see Starting the engine

Mounting the L grip (BC 225 L) (Fig. 2)

„Bike“ grip (Fig. 2) (Fig. 3)

1. Place the rubber sleeve over the support bar.
1. Place the rubber sleeve over the support bar.
2. Screw together the lower half of the grip and the top half above the rubber sleeve using the four Allen screws.
2. Screw together the lower brace and the grip holder over the rubber sleeve using the four Allen screws.
3. Place the grip rod into the grip holder.

Mounting the guard (BC 225 L) (Fig. 3)

4. Fasten the upper brace onto the grip holder using the four Allen screws.
1. Fix cover and mounting sleeve with the center hexa gon socket screw on the stem and tighten.

Mounting the cutting blade (Fig. 5)

2. Screw protection cover with the remaining two hexa gon socket screws
1. Place the drive plate onto the guide pin on the drive shaft.
2. Place the cutting blade onto the drive plate so that the hole in the cutting blade is positioned precisely on the guide circle on the drive plate.

Mounting the string head (BC 225 L) (Fig. 4)

1. Hold the driver disc with your hand.
3. Push the flange onto the cutting blade so that the flat side faces the cutting blade.
2. Screw the string head onto the guide pin. Caution: Left-hand thread.
4. Fit the fan washer.
5. Secure the clamping nut onto the guide pin. To do this, insert the Allen key into the relevant holes and tighten using the spark plug wrench provided. Cauti on: left-hand thread!
6. Secure the nut with the cotter pin.

Mounting the guard (Fig. 6)

1. Fix protection cap with medium screw on the hand lebar.
2. Protective cover with the remaining two hex screws and hex nuts tighten.

Mounting the string head (Fig. 7)

Show 10 more labels / short text on this page
1 String head · 1 String head · 2 Driver · 2 Drive shaft · 3 Guard · 3 Guard · 4 „Bike“ grip · 4 “Bike” grip ·  · 
Page 4 of the Al-ko BC 225 L user manual — Preparing a fuel mixture
Pagina 4 · klik om te vergroten
Pagina 4
1. Place the drive plate onto the guide pin on the drive shaft.

Only use fuel in a ratio of 25:1.

2. To lock, insert the Allen key into the hole in the dri ver disc.
1. Pour petrol and a branded 2-stroke oil into a suitable container in accordance with the table.
3. Screw the string head onto the guide pin. Caution: left-hand thread!
2. Mix both parts th oroughly.

Table of fuel mixing ratios

Adjusting the shoulder strap (Fig. 1)

Mixing procedure Petrol Mixing oil

1. Push the shoulder strap over your left shoulder.
25 parts petrol1 part mixing oil 2-stroke mixing oil

1 l 40 ml

2. Hook the locking hooks into the eyelet (1-6).

3 l 120 ml

3. Check the length of the shoulder strap by making a number of swinging movements without switching on the engine. The string head or cutting blade must move parallel to the ground.

5 l 200 ml

Starting the BC 225 L and BC 225 B

„ „ Before use, ensure that all screws, nuts and bolts on the

device are securely fastened „ „ The machine must not be operated with loose, damaged

or worn cutting equipment and/or fixing components „ „ Replace damaged or worn parts with genuine spa

Fuel and consumables

re parts. „ „ Always operate the trimmer with the guard.

Safety instructions

„ „ Always observe the operating instructions provided by

the manufacturer of the engine. „ „ Observe local regulations regarding operating times.

„ „ Ensure that no fuel leaks from the engine, tank or fuel

Starting the engine

lines. „ „ Only mix and store petrol in approved containers.

„ „ Do not use any fuel mixture that has been stored for

more than 90 days. „ „ Only refuel outdoors.

„ „ Do not smoke while refuelling.

Before start-up, shorten the cutting string to 13 cm to avoid overloading the engine.

„ „ Do not open the fuel cap while the engine is running

or hot. „ „ Exchange the tank or fuel cap if damaged.

„ „ Always keep the fuel cap firmly closed.

„ „ Only empty the fuel tank outdoors.

„ „ If petrol has spilled out:

„ „ Do not start the engine. „ „ Avoid ignition attempts. „ „ Clean the machine. „ „ Allow leftover fuel to evaporate

Preparing a fuel mixture

 · 

Page 5 of the Al-ko BC 225 L user manual — Starting the BC 225 L
Pagina 5 · klik om te vergroten
Pagina 5

Choke settings:

BC 225 L warm start (Fig. 5) (Fig. 6) 1. Set the ignition switch to the “Start” position. 2. Set the choke to „RUN“. Pull the starter cord - the en gine will start.

CHOKE RUN

„ „ Engine does not start:

„ „ Set the choke to the “RUN” position. „ „ Pull the starter cord 5 times. „ „ If the engine still does not start:

1. Place the strimmer flat on the ground away from any other objects.

„ „ Wait 5 minutes and then try again with the gas lever pressed down.

2. Ensure that the cutting tool is not in contact with any objects or the ground.

Refer to the “Troubleshooting” chapter.

3. Ensure that it is stable.

Switch off the engine (Fig. 5)

4. Hold the device with your left hand. With your right hand, grip the starter cord.
1. Release the gas lever and let the engine idle.
2. Set the ignition switch to “STOP”.
5. Do not stand or kneel on the support.

„ „ Always pull the starter cord straight out. Never allow it

to snap back abruptly.

Starting the BC 225 L

Starting the BC 225 B

BC 225 L cold start (Fig. 5) (Fig. 6)

BC 225 B cold start (Fig. 8) (Fig. 9)

Al-ko BC 225 L — Starting the BC 225 L diagram (page 5)
Afb. 3 · Starting the BC 225 L
1. Set the ignition switch to the “Start” position. 2. Press and hold the throttle lock, press the throttle. 3. Set the choke to the “CHOKE” position.

1. Set the ignition switch to the “Start” position. 2. Lock the gas lever: „ „ Press and hold the throttle lock „ „ Press and hold the throttle „ „ Press and hold the „Lock off“ switch „ „ Release the throttle The throttle runs at full throttle. „ „ Release the „Lock off“ switch. 3. Set the choke to the “CHOKE” position. 4. Press the cold start membrane pump 10 times. 5. Pull out the starter cord 2 or 3 times until the engine starts (ignites) audibly for a brief time. Pull the cord briskly with uniform force. 6. Once the engine has started: set the choke to “RUN”.

4. Press the cold start membrane pump 10 times. 5. Pull out the starter cord 3 or 4 times until the engine starts up (ignites) audibly for a brief time. Pull the cord briskly with uniform force. 6. Once the engine has started: set the choke to “RUN”. 7. Pull out the starter cord until the engine starts. 8. If the engine does not start, repeat steps 1 to 7.
Page 6 of the Al-ko BC 225 L user manual — Safety instructions
Pagina 6 · klik om te vergroten
Pagina 6
7. Pull out the starter cord until the engine starts. 8. If the engine does not start, repeat steps 1 to 7.

„ „ Never work on a slippery hillside or slope.

„ „ Never use the device in the vicinity of highly flammable

liquids or gases – Risk of fire and/or explosion! „ „ After contact with a foreign object:

BC 225 B warm-start (Fig. 8) (Fig. 9) 1. Set the ignition switch to the “Start” position. 2. Set the choke to the „RUN“ position. 3. Pull the starter cord quickly a maximum of 6 times - the engine will start. Keep the gas lever pressed down fully until the engine runs smoothly. „ „ Engine does not start:

„ „ Switch off the engine.

„ „ Examine the device for damage.

Lengthening the cutting string

1. Let the engine run at full throttle and tap the string head on the ground. The cutting string will be extended automatically.

„ „ Set the choke to the “RUN” position. „ „ Pull the starter cord 5 times. „ „ If the engine still does not start:

„ „ Wait 5 minutes and then try again with the gas lever pressed down.

The blade on the safety shield shortens the cutting string to the permissible length.

Refer to the “Troubleshooting” chapter.

Cleaning the guard

1. Switch off the device.

Switching off the BC 225 B engine (Fig. 8)

4. Release the throttle and allow the engine to idle.
2. Carefully remove mowing debris with a screwdriver or similar tool.
5. Switch the ignition to „STOP“.

Clean the guard regularly to prevent the shaft tube from overheating.

Trimming

Instructions for use

1. Examine the terrain and determine the desired cut ting height.

Always let the engine run in the upper speed range during trimming and cutting.

2. Guide and hold the string head at the desired height.
3. Swing the device from side to side in a sweeping, scythe-like motion.

Safety instructions

4. Always keep the string head parallel with the ground.
1. Hold the device so that it is tilted forward at a slight angle and moves just above the ground.

„ „ Persons who are not familiar with the trimmer should

practise handling it with the engine switched off „ „ Wear appropriate working clothes

2. Always trim away from your body.

„ „ Always ensure stability when working.

Trimming along fences and foundations

„ „ Always operate the machine with both hands.

„ „ Keep body and clothing away from cutting parts.

„ „ Keep third parties away from the danger area.

„ „ Never hold the string head higher than knee level when

the device is in operation. „ „ Do not spray the unit with water and protect against rain

1. Move the unit slowly and carefully without allowing the cutting string to hit any obstacles.

and humidity. „ „ When mowing on sloping ground, always stand downhill

of the cutting device.

 · Close trimming · 

Page 7 of the Al-ko BC 225 L user manual — Fuel filter
Pagina 7 · klik om te vergroten
Pagina 7

Trimming around tree trunks

Do not use the cutting blade in the vicinity of fixed obstacles – Never use blunt cutters and avoid uncontrolled contact with foreign bodies. Otherwise there will be an increased risk of the equipment kickback, which could throw the machine around. As a result the operator could be make involuntary movements, which could lead to serious injuries.

1. Guide the device slowly and carefully around tree trunks, ensuring that the cutting string does not touch the tree bark.
2. Mow from left to right around tree trunks.
3. Cut grass and weeds with the tip of the string and keep the string head tilted slightly forwards.

Trimming along stone walls, foundations and tree leads to increased string wear.

Dense vegetation, young trees or brushwood can jam the cutting blade and stop it turning.

Mowing

„ „ Avoid jamming by noting the direction in which the veg

1. Tilt the string head to the right at an angle of 30 degrees.

etation leans and then cutting from the opposite side. „ „ If the cutting blade becomes entangled during cutting:

2. Move the handgrip to the desired position.

„ „ Switch off the engine immediately.

„ „ Hold up the device so that the cutting blade does not jump or break.

„ „ Push the caught material away

Maintenance and care

Mowing with the cutting blade

„ „ Clean the device after every use with a brush and a dry

When mowing with the cutting blade, the cutting blade should be guided in a curving horizontal motion from one side to the other.

cloth. Do not use cleaning agents or water.

Air filter

„ „ Use the shoulder strap.

1. Remove the star screw, take off the cover and take out the air filter.

„ „ Check the safety hood and cutting blade for correct

installation. „ „ Wear protective clothing and eye protection.

2. Clean the air filter with soap and water. Do not use petrol!

Do not use weed cutter blades for cutting brush wood and young trees!

3. Allow the air filter to dry.
4. Install the air filter in reverse sequence.

Fuel filter

5. Completely remove the fuel cap.
6. Empty the remaining fuel into a suitable container.
7. Pull the filter out of the tank with a wire hook.
8. Remove the filter with a twisting motion.
Show 7 more labels / short text on this page
Jamming ·  ·  ·  ·  · Avoiding recoil · 
Page 8 of the Al-ko BC 225 L user manual — Disposal
Pagina 8 · klik om te vergroten
Pagina 8
9. Exchange the filter.

Recommissioning

Carburettor adjustment

1. Remove the spark plug.

The carburettor is optimally adjusted at the factory.Spark plug (BC 225 L, Fig. 7) (BC 225 B, Fig. 4)

2. Quickly pull the starter cord to remove leftover oil from the combustion chamber.

Spark plug gap = 0.635 mm [0.025”].

3. Clean the spark plug, check the electrode distance.
4. Re-install the spark plug, replace if necessary.
10. Tighten the spark plug with a torque of 12-15 Nm.
11. Push the spark plug connector onto the spark plug.
5. Prepare the device for operation.
6. Fill the tank with the correct fuel/oil mixture (25:1).

Sharpening the string cutter blade

Troubleshooting

1. Remove the cutting blade from the guard.
2. Clamp the cutting blade in a vice and sharpen it with a flat file. File in one direction only.

Engine does not start

„ „ Incorrect starting procedure,

observe the operating instruc tions.

Storage

„ „ Clean the spark plug and the

„ „ Empty the fuel tank before long periods of storage

air and fuel filters.

(over the winter) „ „ Only empty the fuel tank outdoors

Engine starts but does not continue to run

„ „ Set the lever to RUN.

„ „ Allow the engine to cool down before storage

„ „ Clean / adjust or replace the

spark plug.

1. Empty the fuel tank.
2. Start the engine and let it idle until it stops.

„ „ Clean or exchange the filter.

Engine starts but does not run with full performance

„ „ Set the lever to RUN.

3. Let the engine cool down.

„ „ Clean or exchange the filter.

4. Loosen the spark plug with a spark plug socket.
5. Pour a teaspoon of 2-stroke oil into the combustion chamber. Pull the starter cord slowly several times to distribute the oil in the interior of the engine.

„ „ Clean / adjust or replace the

spark plug.

6. Insert the spark plug again.

„ „ Use the correct fuel mixture

(ratio 25:1).

7. Thoroughly clean and service the device.
8. Store the device in a cool dry place.

Faults that cannot be corrected with the help of this table must be rectified in an authorized, specialist workshop.

Disposal

Machines that are no longer required must not be disposed of with household waste!

Packaging, machine and accessories are manufactured using recyclable materials and must be disposed of accordingly.

Show 4 more labels / short text on this page
Problem Correction · Motor runs spasmodically · Excessive smoke · 
Page 9 of the Al-ko BC 225 L user manual — Warranty
Pagina 9 · klik om te vergroten
Pagina 9

EC DECLARATION OF CONFORMITTY GB

We hereby declare that this product, in the form in which it is marketed, meets the requirements of the harmonised EU guidelines, EU safety standards, and the product-specific standards..

Product Trimmer Serial number G2302305

Manufacturer AL-KO Geräte GmbH Ichenhauser Str. 14 89359 KOETZ DEUTSCHLAND

Executive Officer Andreas Hedrich Ichenhauser Str. 14 89359 KOETZ DEUTSCHLAND

Model BC 225 L BC 225 B

EU directives 2006/42/EG 2004/108/EG 2000/14/EG 2002/88/EG

Harmonised standards EN ISO 11806 EN ISO 14982 EN ISO 22867 EN ISO 22868

Sound power level measured / guaranteed EN ISO 3744 BC 225 L 98 / 113 dB(A) BC 225 B 105 / 109 dB(A)

Conformity evaluation 2000 /14/EG Anhang V

Notified body TÜV Rheinland Product Safety GmbH Am Grauen Stein 51105 Köln Germany

Wolfgang Hergeth, Managing Director

Warranty

If any material or manufacturing defects are found during the statutory customer protection period, we will either repair or replace the equipment, whichever we consider the more appropriate. This statutory period may vary according to the legislation in force in the country where the equipment was purchased.

Our warranty is valid only if: The warranty is no longer valid if:

„ „ The equipment has been used properly

„ „ The equipment has been tampered with

„ „ The operating instructions have been followed

„ „ Technical modifications have been made

„ „ Genuine replacement parts have been used

„ „ The equipment was not used for its intended purpose (for

example, used for commercial or communal applications)

The following are not covered by warranty:

„ „ Paint damage due to normal wear

„ „ Wear parts identified by a border XXX XXX (X) on the spare parts list

„ „ Combustion motors – these are covered by a separate warranty from the manufacturer concerned

To make a claim under warranty, please take this statement of warranty and proof of purchase to the nearest authorised customer service centre. This warranty does not affect the usual statutory rights of the customer relative to the seller.

Kötz, 2014-12-15 · ┌──────┐ └──────┘

Probleemoplossing

Probleemoplossing

Veelvoorkomende problemen, mogelijke oorzaken en oplossingen.

ProbleemMogelijke oorzaakOplossing
Engine does not start„ Incorrect starting procedure, observe the operating instruc­ tions. „ Clean the spark plug and the air and fuel filters. p.8
Engine starts but does not continue to run„ Set the lever to RUN. „ Clean / adjust or replace the spark plug. „ Clean or exchange the filter. p.8
Engine starts but does not run with full performance„ Set the lever to RUN. „ Clean or exchange the filter. p.8
Motor runs spasmodically„ Clean / adjust or replace the spark plug. p.8
Excessive smoke„ Use the correct fuel mixture (ratio 25:1). p.8

Vraag stellen over de Al-ko BC 225 L

Eigenaren en ons team reageren doorgaans binnen een dag — en uw vraag helpt ook de volgende persoon.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Nog geen vragen over de Al-ko BC 225 L

Stel als eerste een vraag — andere eigenaren of ons team geven antwoord.

Origineel document

Al-ko BC 225 L handleiding-pdf

264 pagina's·9.2 MB·Grastrimmer·PDF
Klik op een bovenstaande pagina om deze hier te openen
Pagina 1 / …
100%
Pagina's laden…